I'm looking into a rare issue on the BBC micro:bit V2 which uses the nRF52833 as its (application) microcontroller. I used to be familiar with some CPUs from the 80s but my...
I have shifted from silicon labs for BLE project. In Si labs we have burn BLE bootloader and BLE application separately. Do i need to do the same here in nrf controller? If...
I am unable to detect any i2c device when connected to the Nordic nRF54L15 DK kit. I have change the voltage from 1.8v to 3.3v and Tried and explore other pins in Port 0 and...
Hi All,
I have to implement an I2C Slave on my nrf52833 BLE project which is currently working (SDK 2.9.2)
I need some confirmation with the following step:
I have...
I am using the 54l10 chip, and after compiling the project, I will receive a hex firmware and a zip update package. The bin firmware and hex firmware in this update package...
Hi,
I faced with an initialization issue of combination two features: MCUMGR and UART_ASYNC_API. I get a crash right after the FW starts. It looks like the SW configuration...
Hello, I need to configure and compile a sample to send an audio stream (mp3) to the I2S interface.
I tried to put together some configuration from other samples but no...
Hello,
Is this the correct setup? What else will I need to do to make it work (e.g. it says something about the MCU will detect the external board and then programm/debug...
I want my device to pair only with a single central device at a time. So once it gets paired, it should not be able to pair with any other device. For this purpose I use directed...
Hi community,
I'm studying the possibility to be able to link multiple central devices to one peripheral. As it defined in the s130 soft device description ( www.nordicsemi...
I upgraded Arduino IDE to 1.6.8 version, it was automatically set up Programmer AVRISP mkll, in previous version I can see that was Atmel STK500 development board
in Tool...
Hi.
I'm trying to get audio controls (mostly volume up/down) to work with apple and android phones. I've used as base your HDI keyboard example.
It seems to work OK...
I have a BLE peripheral application based on the nRF51822, running Soft Device S110 with SDK 8.1.0. The centrals are mobile apps, one on Android 5.0, one on iOS 8.4.1.
...
I'm using the UART driver (drv_uart.c) provided with the nRF5 SDK 11.0.0 on a nRF52 chip and once a NRF_DRV_UART_EVT_ERROR event is received, the receiver seems to be stuck...
Hello all!
I'm researching Radio Notification. I had read define and tutorial . But, It don't make me clearly.
Could you explain more deeper about Radio Notification...
Hi,
I just upgraded the SEGGER RTT source files from V4.98e to the new V5.41b for a nRF51DK project using gcc/Makefile. When linking the (now quite large) program, I got...
Hello,
I am using S110 8.0 soft device and using the example Nordic_UART. I am able to compile the project file in KEIL and flash it onto my board. I don't see any errors...
We are using the low power comparator on NRF51882 RayTac Module (Vcc=3.3V, Vref = 4/8), with which we are making a precise high impedance measurement!
I found some documentation...
I've been sending various BLE addresses to the nRF51 and am getting some inconsistencies of what addresses are being deemed valid.
I am using BLE_GAP_ADDR_TYPE_RANDOM_STATIC...
I am using uVision 5.18a with MDK-Lite ARM toolchain and I downloaded nRF examples for SDK 11.0.0-2.alpha with Pack Installer.
Then I tried to compile " /ble_peripheral...
Hello everyone,
I would like to know, if it is possible to send data (power data) from a NRF52-DK to a Garmin Display Device. Do you know any application, project example...
I wanted extract BLE_GAP_AD_TYPE_128BIT_SERVICE_UUID_COMPLETE that i receive while scanning and compare it with 128 bit service uuid that i defined.
i have seen how ot...
