Hello, I am a beginner to nRF54 series (currently have nRF54L15DK) and to understand the concepts and communication between nRF devices and iOS software with bluetooth LE...
I have a preset stored in CMakePresets.json:
When I go to create a new build configuration with the preset, the extension creates an Extra CMake Arguments row with:
...
Hello Nordic Team,
For my application, I am using two nRF54L15 chips with one configured as a master and the other a slave. For the remainder of this post, I will be discussing...
Using VSCode with nRF Connect extension on Ubuntu Linux 22/04 with nRF SDK 3.0.1 and nRF Toolchain 3.0.1 installed I can create a build configuration for Zephyr's hello_world...
Hello DevZone team, I recently received a new nPM1300 Eval Kit (PCA10152, 1.3.0, 2025.19) and connected it the first time following the documentation ( docs.nordicsemi.com...
Hi everyone, I'm trying to set up a bootloader chain using sysbuild (NSIB → MCUboot → APP) so that MCUboot can act as an upgradable bootloader. I'm working with the nRF54L15...
Hello, I am using an I2S PDM Mic and trying to send the I2S Data over BLE using Segger Embedded Studio. The I2S Program that I have generated is working ok. I have verified...
I am using SDK 2.9.1. I wanted to follow this tutorial:
https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate/lessons/lesson-7-device-driver-model/topic/exercise...
Hello Nordic friends,
currently I use NRF7002-EK successfully in my bare-metal environment, but for debugging, I'm considering using the EB instead of the EK if the edge...
Hi All,
I am currently exploring on nrff4l15 SOC and have its dev kit.
I read on this forum ( multiple tickets ), that there is a support of NSIB. I would like to know...
Hello, I have an application running on an nRF9160. The current app was built using NCS 1.7.0 with the L2M2M Carrier Library enabled. I'm upgrading the application to use...
Hello,
We are developing a Cellular IoT device based on nRF9160 SiP. Essentially it is a battery powered temperature and humiduty sensor, that sends the measurement data...
Hello everyone,
we have an in-house HW with the nPM1300. Both load switches are configured as LDOs as described in datasheet chapter 9.3 configuration 1.
LDO1 is used...
Hi,
I have successfully implement the BLE video transfer using nrf70-wifi-ble-image-transfer-demo .
I can receive the image using the Android-Image-Transfer-Demo application...
I am using VSCode with SDK 2.9.1. I have added the spi21 to the device tree UI editor. When I choose the MOSI, MISO and SCLK, they all show up in the visual representation...
1. Our system is configured with circuit config3 of the nRF52833 WLCSP, where an external power supply of 1.8V is applied to VDD.
Power sequence : USB connection -> VBUS...
Hello,
I'm using the SLM application with an NRF9160. I'm sending AT commands for MQTT publish. After ~10hours the device reboots.
The setup AT commands from powerup...
Zephyr Version 3.7.99, Zeyphr SDK v0.17.0
Thread Version v1.4
Matter SDK Version 1.4
After the switch from Matter SDK version 1.3 to 1.4, the NVS module under Zephyr...
We are currently developing a project using the nRF52832 as the microcontroller, Segger Embedded Studio version 5.42a as the IDE, and the nRF5 SDK 17.0.2. We began by creating...
Hi,
I need to use two or more different event lengths for different modes. The event length should be set based on the mode before establishing a connection. I found that...
