While building the program I get this error message: "DT_N_NODELABEL_cpucell_cpuapp_ipc_shm_trace_REG_IDX_0_VAL_ADDRESSU" As far as I can tell, this error message is releated...
Hello,
I have a pin on port 1 of the nrf54l15 that I am bitbanging for a custom tx/rx 2-wire protocol. I have already managed to implement the tx capability and I was hoping...
Hi,
I've got two ESB transceivers talking to each other - a PTX on nRF52832 (E73 module) and a PRX on nRF52810 (Holyiot module, the "tag"). Both chips can obviously TX and...
Hi Nordic team,
I am currently researching Bluetooth Channel Sounding, where I have setup two nrf54LM20-DK as intiaitor and reflector respectively.
I am using NCS 3.3...
Hi:
I use sdk ncs3.3.0 and nrf54lm20dk.
Failed to return using AA dfu_target_init.
OTA firmware is zephyr.signed.bin.
I: DFU header I: 3d b8 f3 96 00 00 00 00...
Hi there,
I'm evaluating the latest release of NCS ZigBee addon version 1.4.0, wanted to try and migrate my existing project to the newer version. I've encountered the following...
Hello,
I've been asked to create a new ticket for this. It follows on from
@ Erlend Isachsen asked:
So before marking this problem as resolved, it would be nice to be...
Hi Nordic expert,
We are K5DET1/3/5/7/9/11 output high level, then string 10K resistor, K5DET2/4/6/8/10/12 through the mercury switch to read this high level, while adding...
Hi,
According to the documents of NCS, CoAP Server sample uses native OT CoAP API while CoAP Client sample uses Zephyr CoAP API, and the Zephyr CoAP API is recommanded....
I've googled all over, and I'm having a hard time finding any documentation that digs into how to use the nRF Connect SDK. Most documents point to examples, however the wealth...
Hi，
I developed with ncs 2.1 samples esb ptx and prx using nrf52840 make a low latency application，There are two problems
①On the ptx side, packets are sent twice in...
Hi, in our project we have to send some raw data to one node to other node using zigbee. So i have checked every single example but it doesnt match with what i need. I have...
Hi,
I'm trying to write a simple python application on Windows 7 that communicates with a BLE peripheral running Nordic UART Service. I'm using the nRF dongle and pyserial...
Hi,
I'm trying to config my SAM-M8Q with an array of HEX.
It's work beautifully with app_uart_put like the picture below.
However, when I try to implement LIBUARTE...
Hii
I have a problem pass the address while advertising
I should pass the adress using 9160_dk
However, in main.c there is this line:
#define DEVICE_NAME "Nordic_UART...
Hi there, I'm trying to find a hardware integration guide that details min max specs for the IC and also details the RF output pin impedance so I can match to my board stackup...
I checked out the nrf github repo and tried to build the nrf_dm sample for the nRF 52840 dev kit which is what I have
In VSCode I chose "Add an existing application" and...
Hi,
As the title, I can see Mesh Proxy service in nRF connect app, after provisioined device by nrf Mesh app. But when I send data to Mesh Proxy Data In, It disconnect immediately...
I followed the document and downloaded nRF Connect for Desktop in Ubuntu 18.04.5.
Then I changed the permission of nrfconnect-3.11.1-x86_64.appimage to "allow executing...
Hi,
We have an issue that is puzzling us.
The symtoms are the following.
If we flash v1 of our application (using Segger Link) to our target, it works correctly, no...
Hello,
I am experiencing a power issue after the first ADC sample is triggered. Sampling 2 ADC channels using PPI and TIMER as the triggering mechanism. Here is a capture...
nRF SDK 17.1.0 sd140 7.2.0
I'm working on adding OTA DFU to ble_app_uart. I had my own custom service that was working and then added on the DFU files like ble_dfu.c and...
