I have a nRF54l15dk development board and a custom nRF54L15 board that I am trying to load a Matter Template sample application on. I have created a custom board device tree...
I have observed that when using the ESB protocol at maximum throughput, the measured power consumption decreases as the PHY data rate increases: 4 Mbps consumes less power...
Subject: Connecting LPCOMP CROSS event to TWO DPPI-driven tasks (GPIOTE toggle + TIMER count) simultaneously — only the last-configured one fires
Chip: nRF54L15 SDK: nRF...
Dear Nordic, i have started my application with toolchain & sdk both v3.3.0, using custom services & charachteristics, with BLE advertising @500ms interval works fine. but...
While configuring a scene, the blind device is not visible in the scene settings screen, so it is not possible to set or save the blind position as part of the scene.
Steps...
Hi,
I've been using NRF Cloud without issues (Pro subscription) and I am no longer able to login my NRF Cloud account. I tried changing password and use different type of...
software:nrf connect sdk 1.9.1
hardware:nrf5340
hi professor,
I use the nrfx_gpiote_in_init(GPS_TS_PIN, &config_in, gps_timepulse_handler) but return NRFX_ERROR_NO_MEM...
Hello Nordic：
I wanna to know what actions a thread have done from reset to joined a thread network.
I observed the air packets by using Wireshark. I found a router(rx_on_when_idle...
The device is connected to the PC via FTDI chip. The device manager shows the COM port. LTE Link Monitor v2.0.1 cannot find the connected device on SELECT DEVICE. The windows...
Hello.
I am using nrf52832 (s132 v7.0.1, SDK v17.0.0) as a peripheral and developing.
I am using nRF Connect to communicate with the peripheral nRF52832.
One of the...
Hi,
I have tried to follow the below tutorial ( https://www.youtube.com/watch?v=hY_tDext6zA&t=933s) . While I am trying to advertise the ble by following that webinar. I...
Hi,
I want to use BLE as both connectable mode and non-connectable mode in the same application. Is it possible to do that?
Is it possible to switch connectable BLE mode...
Hello!
I have a nRF52840DK with a custom board. I have installed nRF 1.9.1. I have read about the twi_scanner but I don't find that code in my installation! Did I do anything...
Hi,
I am trying to download SUPL client library but got an email that my request was denied. I've used the same email address as the one here. Can you please advise?
Kind...
i need help.
We use nrf52840 and DK17.0.2
Using saadc with oversampling x8 , Single-ended mode.
Question
When Event monitoring using limits , Is the timing at which...
I'm using three low power PWM instances driving three separate IO pins open an nRF 52810 and need to be able to re-configure each of the channels on the fly to select opposite...
https://devzone.nordicsemi.com/f/nordic-q-a/69596/device-initialization-problems/285611#285611
had gone through above thread.
I am struck exactly at this point.
i...
Hi
I am using 52832 peripheral role.
sdk16.0
ble_uart add one character 0xff03 which have notify attribute
have these function
1. Use connectable broadcast on no...
Dear Nordic Engineers
I study central code,I find a param ble_gap_evt_adv_report_t
I can understand other param of ble_gap_evt_adv_report_t,but I don't understand set_id...
The NFC pins of my nRF52840 MCU have been set to be used as GPIO pins through the NFCPINS register. I can toggle the GPIO lines just but I find that after power on that the...
