What this ticket reports
We ship a battery-powered nRF5340 product using the nRF Connect SDK's documented production security configuration: immutable bootloader (NSIB/b0...
NCS 3.4.0 - Thingy91X
If I configure the sysbuild with sysbuild.conf
SB_CONFIG_BOOTLOADER_MCUBOOT=y SB_CONFIG_SECURE_BOOT_APPCORE=n
it builds, but on "west flash" I...
I am working with the NRF52832 DK with a Tag-Connect 3 prong cable attached to the debug port.
I have found a bug that has so far been 100% reproducible. It already happened...
Hi team,
I recently purchased some nRF54LM20A units and I am currently working on interfacing them with a W5500 Ethernet module over SPI. However, I am facing difficulties...
I just programmed 2 Boards.
One Peripheral advertising with 1m Phy and other peripheral with s8 codded phy.
Using NRF connect app and wire sharc I made sure that I really...
I’m using NRF Connect SDK 3.2.4 with the nRF54L15-DK. I’ve successfully used the nrfx_gppi_conn_alloc() and nrfx_gppi_conn_enable() APIs to connect a timer to a GPIOTE output...
Hi,
I am using BL653 dvk to write an application for SPI, In my prj.conf, I added below parameters:
Now when I am debugging SPI master code, execution enters the file...
We are performing a preliminary power analysis with this device and have questions regarding the power consumption reported in the Product Specification. For example, the...
I've been struggling with enabling HTTP support on the serial_lte_modem. I've tried using various versions, currently I'm using NCS 1.8.99. I edit the prj.cnf to include CONFIG_SLM_HTTPC...
Hi,
I use nRF52840 and SoftDevice s140 (7.2.0). I use SEGGER Embedded Studio to compile a project written in C++. But lately I've been having trouble debugging. For example...
i've been test code from nrf51-app-button-example/main.c at master · NordicPlayground/nrf51-app-button-example (github.com) but not effect when presss any button.
I am new to Zephyr and Nordic. I onserved that to use variuos APIs it is required to declare in prj.conf file. But, where is the list and document of various commands woth...
Hi
I have a Nordic nRF51 as a Peripheral.
I have it open advertising until it connects for the first time to an Android handset.
When a connection is made it stays...
When I switch to any branch other than 1.8.0-rc2, I get the following notification:
"This workspace requires version 1.8.0-rc2 of the nRF Connect SDK, but it isn't installed...
I am developing a BLE Peripheral device using the nRF52805 and have just discovered that neither of the two SoftDevice packages offered for this chip have support for extended...
After compiling an example and attempting to connect to my board, VS Code won't connect to my board. It is definitely recognized by my computer, and the Programmer application...
Hello everyone,
currently I am working on my application which is based on the multirole example and with the SDK17.1. My target is if one device connected to another the...
what is the external 32.768khz crystal tolerance range for BLE? we have a product, it easily disconnect with another one when the distance is 5m, the PPM is -120ppm, fine...
Hi,
The project is a multi-link environment of nrf52840, The 7 peripherals has the task of send data constantly of a sensors. All is working on coded_s8.
The objective...
Hi
Which example Implement the central whitelist function?Is the whitelist of the center mainly used to connect the slave device which address is the same as the address...
Trying to activate iBasis SIM in the nrfcloud.com, getting message "User cannot be updated" with no extra information.
I'm in Dublin, Ireland.
An activation dialog keeps...
