Hello,
I've been asked to create a new ticket for this. It follows on from
@ Erlend Isachsen asked:
So before marking this problem as resolved, it would be nice to be...
I am developing on the nrf9151 with SDK v3.4.0.
The device I am developing will be moving trough all of europe . My goal is to speed up the `AT+CFUN=1` conenction part of...
HI
I am currently carrying out secondary development for PAWR based on NCS 3.2.1. I understand that its communication adopts frequency hopping. I would like to ask whether...
NCS-3.4.0, on nRF5340, custom board losely based on PAN1783. No RTT backend, BLE stack works properly:
RTT enabled, BLE stack reads some garbage:
Printing is done...
Hello, our design does not use the USB block of the 52833. In the electrical schematic we have connected VBUS (AD2) to GND and we leave D-(AD4) and D+(AD6) open. Due to a...
SDK: nRF Connect SDK v3.4.0 (TF-M v2.3.0) Board: nRF9151 (seen on both nrf9151dk and a custom nRF9151 board) Config: CONFIG_TFM_PROFILE_TYPE_MINIMAL=y, MCUboot with CONFIG_USE_SEGGER_RTT...
I am looking to evaluate Amazon sidewalk on the nrf54L15 dev kit and have also bought both of the Semtech evaluation boards LR1110MB1LCKS and SX1262MB2CAS. The nrf54L15 is...
Hi all,
I got my nrf5340PDK working with the Thread CLI Sample.
I can now connect to the UART interface and issue ot commands.
According to the tutorial Thread: CLI...
In response to a BLE_GAP_EVT_DATA_LENGTH_UPDATE_REQUEST, we have called sd_ble_gap_data_length_update, with the following parameters:
Rx Octets: 251/ Tx Octets: 251
Rx...
Hello everyone, i need to increment a counter each time my button on the nrf534DK is pressed i'm using sdk v 1.7.1 . is there a simple way to do it or a function which supports...
Hello!
I've seen similar posts about this issue: https://devzone.nordicsemi.com/f/nordic-q-a/57105/nrf9160-modem-stuck-in-searching https://devzone.nordicsemi.com/f/nordic...
I am looking to handle low priority interrupts on a single GPIOTE Port Event but when attempting to add the second pin with the same handler i get an error and the handler...
Hi Team Nordic and fellow engineers, I am seeking to find better parts from Nordic RF Transciever lineup
to replace nRF24L01P-R, in order to improve the performance of the...
Hello, I intend to use libuarte under FreeRTOS together with the SoftDevice (SDK 17.1.0). An app_timer is used for the RX timeout. I think there might be an incompatibility...
Hello,
I have a situation where I would like to reset the MCU (nRF52832) under Zephyr. For the most part I use ```sys_reboot(SYS_REBOOT_COLD)```. However, I would need...
Hi,
I just downloaded both versions 1.7.0 and 1.7.1. Compiling asset_tracker_v2 right out of the box with west build -b nrf9160dk_nrf9160_ns --pristine I get the hex files...
I built a game controller hardware for windows . I am supposed to have a few millisec. latency on notifications.
But the latency seems to be noticeable. I have also tried...
Hello everyone!
We've integrated the readout protection to our project, but unfortunately now we don't able to disable it.
The activation code presented below:
...
Hi
I would need to work on Master Branch. I have Toolchain Manager 0.10.1 and I have downloaded nRF Connect SDK 1.7.1.
I know that Toolchain Manger has not Master branch...
In my project an interacting with the ncs 1.6.1 peripheral _uart example and my plan is to ensure that data size being send at a particular time is increased to send at least...
Hello everyone,
I went through the forum and saw some topics regarding the implementation of the characteristic read out over sd_ble_gattc_read. I implemented it as desribed...
