Hi all,
I've built a custom nRF9151 board, which is successfully responding to the basic factory AT commands. It won't accept a CFUN=1 command though, presumably because...
Hello!
I think there is a problem in NCS v3.3.0. nRF54L target, sysbuild build with MCUboot and TF-M, partition layout coming from devicetree (SB_CONFIG_PARTITION_MANAGER...
Hi, I'm developing a keyboard-pcb with NRF52840. I'm doing this as a hobby and are not that experienced with integrated circuits. Anyway, I designed and produced a pcb, but...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
Hi
The TWI driver has a twi_clear_bus() function but the TWIM does not.
I'm getting an I2C error, and need to do I2C soft reset. I'm doing this manually at moment but...
Hello all,
I'm developing a BLE CGMS application based on the experimental example on the SDK folder.
Now I working in the timing characteristics and I could see that...
It looks to me like there's usage of the 32 bit milisecond timer in the mqtt client.
It seems to me that mqtt_elapsed_time_in_ms_get(...) could calculate an incorrect elapsed...
We're using the nRF9160 with an external main microcontroller, and communicating with it over SPI. We're evaluating the lowest power modes of our custom hardware to make sure...
1. I want to minimize current consumption (5uA - 10uA) in nrf52832.
2. We are using the soft devices in it.
3. Please tell me all possible SDK configuration settings for...
Hello all,
I have a BLE central application based on nRF Connect SDK V1.6.1 and a BLE peripheral application based on nRF5 SDK 17.1.0. The peripheral wakes up on interrupt...
Hi
For the qualification we need to know the values of the parameters listed below. Our hardware uses a nRF52805 and can operate in both ESB and BLE mode.
Operating...
Hello Devzome Users,
I have a problem with running my codes on other computers. The project runs on my PC very well which I coded original.
I would like to test it on...
Hello Nordic,
I've acquired several nrf52-dks and I use them almost exclusively to flash with nrfConnect on the PC.
To learn more about nrf programming I started with...
Hi all,
May I know is the antenna array a built in in 5340 DK or not? According to https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/samples/bluetooth/direction_finding_connectionless_rx...
Hey all, I've been learning/working on the 53 and have had some issues adding in the AMG8 example. i've gotten the sensor to work flawlessly on an STM32 & nordic 52 but am...
Hello to all,
I have a question about parsing zigbee commands when they present a payload.
In the Window Covering device I use the define "ZB_ZCL_WINDOW_COVERING_GET_GO_TO_LIFT_PERCENTAGE_REQ...
Hi support team,
I'm learning about distance calculation based on time of flight. I only have nrf52832DK here but i wanted to try. I'm looking for an example of getting...
Hello,
Power Profiler v3.1.3
Windows 10 Home 21H1
On Data Logger tab and , regardless of if a PPK2 has been connected or not, and regardless of any of the values...
Hello,
I have been using the nRF52840 DK board and have designed a PCB based on it. I made a previous post asking some questions before designing the PCB, so this is a follow...
I have developed an application for the nRF52-DK (nRf52832AA) and am now in the process of porting the application to my custom hardware. My custom hardware utilizes the nRF52832AB...
