Hello!
I think there is a problem in NCS v3.3.0. nRF54L target, sysbuild build with MCUboot and TF-M, partition layout coming from devicetree (SB_CONFIG_PARTITION_MANAGER...
Hi, I'm developing a keyboard-pcb with NRF52840. I'm doing this as a hobby and are not that experienced with integrated circuits. Anyway, I designed and produced a pcb, but...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
Hi
The TWI driver has a twi_clear_bus() function but the TWIM does not.
I'm getting an I2C error, and need to do I2C soft reset. I'm doing this manually at moment but...
I recently completed a field-upgrade path from an nRF5 SDK 17.1 application (with the legacy Secure DFU bootloader) to a fresh NCS-based firmware stack, while preserving user...
Hi,
I am looking to design a nRF52833-CJAA (WCSP/ BGA package) board using 4-layer stack.
a) do you see any issue in doing that, vs. 6-layer stack used in nRF52833-DK...
Hey
We encounter problems with the modem not establishing a connection after rebooting the processor for a few times.
Issue:
Firmware is booting normally
Cellular...
It support send periodic advertising with CTE in ncs v1.6.0, but I found that the scanner can establish synchronization with only a tag that sends periodic advertising. But...
Hello fellow Nordic community,
Assume that a given Peripheral ( P) is advertising a BLE GAP signal which allows for multiple connections to be made.
In the vicinity to...
Hi,
I want to connect three coin cell batteries in series to NMP1100 and then connect it to nRF52840 and a temperature sensor.
I want to know, can I charge a supercapacitor...
Hi, I want to simulate the intermittent environment on nFR52850DK. How can I control the power supplement by programming? I mean I want to control when to shut down and when...
Hi Supportor
I want to enable a LAN to receive the ack payload. after proprietary_rf PTX sending
I switch ON LAN in nrf_esb_event_handler, and test the timing in scope...
I cant seem to get the Thingy 91 into boot MCU mode, so that I can update it to the latest firmware. No matter how many times I try turning the unit off and powering up with...
SDK17.0.2+NRF52833
I use nrf52833 to do some thing, P1.09 and p0.11 as two pwm singals to drive two motor and P0.0 as a led pin (high made led light).
the code as following...
Hello guys,
I am developing a BLE Mesh app with nRF52833DK. However, I have recently discovered a problem. It stops working the Mesh iI disconnect USB and then I Connect...
Hi, All,
I saw the following description in the nRF Connect SDK documentation you provided:
That means there are two kinds of controllers on an NCS: Zephyr BLE controller...
1、Does nrf5340's application core and network core support external flash for firmware upgrade?
2、When the application core is upgrading, what is the network core doing...
Dear Members,
I used
E:\nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_uart\main.c
I can see it's running in COM11 from J-link, but I can not see any datas...
