Hi, I am using nrf52832 with softdevice s112 and SDK 17.1.0
Is a ~14-15 µs latency between a GPIOTE PORT event becoming pending (via DETECT / LATCH , SENSE + LDETECT on...
I currently have nRF52/53/54 Development Kits and would like to utilize their onboard J-Link debugger by connecting through the Debug-Out Port (P19). However, I have observed...
Using nRF Connect SDK v3.4.1 with an nRF9151.
CONFIG_NRF_CLOUD_AGNSS currently has unconditional dependencies on:
depends on MODEM_INFO
depends on MODEM_INFO_ADD_NETWORK...
Hi
I am working with nRF Cloud - using a developer account (limited to 10 devices).
After connecting a few times with a device (using a different serial each time),...
I was wondering if the nPM-FG schematic or board design is available, I'm interested in using it to profile a few CR123A's.
The docs suggest the firmware/schematic/layout...
Hi,
On nRF Connect SDK 2.7.0 ( sdk-nrf v2.7.0 , Zephyr v3.6.99-100befc70c74 ), enabling the non-minimal TF-M profile causes WPA2-PSK association to fail during the 4-way...
Hello,
I am new to development with Nordic board. I have evaluation board from u-blox which is EVK NINA-B406 and I have installed Segger Embedded Studio IDE for development...
Hello,
I have been trying for days to program my nrf51422 project without much success. I am using a Jlink programmer. I have connected VTREF, GND, SWCLK and SWDIO from...
Hi,
I know that this question has been asked before but I was wondering if someone can help me understand if the problem is from the connections on my board or my chip...
I am developing a fairly complex app which involved having a lot of logging using the NRF_LOG macros with the UART backend. I am using the nRF52 DK as my platform with nRF...
My app is based on ble_app_hrs_rscs_relay, i.e. the nRF52 DK is acting as central and peripheral at the same time.
SDK 17.0.2, SD S132 v7.
I have a service running there...
Hello, Can your tell me is it possible make three from one device at the same time ? If is not, can I make multiple connection with profiles which support multiple connection...
My goal is to synchronize the clocks of several nodes in a mesh network. I would like the client node to distribute the current time to all the server nodes in the network...
I am trying to run nRF9160: Azure IoT Hub — nRF Connect SDK 1.6.99 documentation (nordicsemi.com) on thingy91. I have followed Azure IoT Hub — nRF Connect SDK 1.6.99 documentation...
Hi,
I am looking at the product brief for nRF21540 and found "nRF21540 Development Kit" and "nRF21540 Evaluation Kit".
Where can I get the H/W information for them,...
Hi,
We want to implement a smart energy meter by using a mesh network including 200 nodes (nrf52840). What is your suggested protocol to do this?
Thank you in advance...
Hi! We're working on a BLE product which is intended for use in the US. This product uses an nRF52833 SOC, with some external components on a PCB we've designed with a printed...
I'm trying to evaluate a Nordic BLE module for a new battery powered project while waiting to establish a connection to a base station device. It seems like your lowest powered...
Hello,
When we tried to increase the Security level from SEC_OPEN to SEC_SIGNED_MITM, it will output error 0x6 which is "Not supported". So how can I do to support a higher...
We are developing AoA direction finding with nrf52833 and antenna array. We also want to include Wifi connectivity to our receiver, having nrf52833 + antenna array. Which...
Hello,
I want to perform NRF52840 Firmware update remotely. I refer to link .
I want only normal http OTA update without encryption for prototype testing. Is there any...
