Device : wearable IOT device
Battery capacity : Max 4.2V (Typ. 3.7V)
BLE Tx Power : Tx power is highest when the battery capacity is 4.2V (measured in air, not conduction...
Hello Zephyr Community,
I am trying to contribute a new sensor driver for the **AMS AS7341 Spectral Sensor** to Zephyr (using **NCS v3.2.2 / Zephyr**), and I would appreciate...
Hello
I need some advice on FOTA via BLE on the nRF54LM20B. I use SDK v 3.3.0, building /ns variant.
I managed to get FOTA working to upload an updated image via BLE,...
I am using the nRF5340 development board to program the LBS example from the NCS SDK2.7. After system-off, the current is still several tens of microamps, which differs from...
When trying to add the device to the Nordic Cloud Device Management interface, I get the following error.
"There was an error adding your device: No device found for this...
So I have two questions. My first is on the impedance matching network on different pcb stackups. So wouldn't I need a different matching network for a different pcb stackup...
We use the NRF Mesh Android Library (and are developing with iOS version as well). An issue that we are running into on a small number of devices is that the library things...
Hi teams,
I am developing with Mesh SDK 4.0.0, and suffers from random fault during long-term test.
The last readable callstack position is the below.
The callstack...
I am currently trying to use a nordic semi ppk and nrf52840 to read current in the nordic semi power profiler software. I am able to flash the DK successfully (while P22 is...
I have a 9160 DK board with lte_ble_gateway on the 9160 side and hci_lpuart on the 52840 side. It works as far as being able to send and receive BLE messages but it has faults...
Hello,
Previous revisions of the nRF SoC's such as nRF52840 and nRF52832 have had specifications for certain IO to be low frequency < 10Khz and standard drive only because...
Hello
I'm facing an issue with app_timer_start. Indeed, with small values, sometimes, the app_timer_start won't start the timer. As a result, the interrupt handler is not...
Online Manlio 6 minutes ago
Hi,
I add NFC to my project with freertos. The initialization of nfc is ok. After running few seconds ,it hang. If I comment the usr_nfc_init...
Hello,
I work with the ATE using Algocraft WN series programmer.
It has directly access to GPIO registers through SWD interface with WRITE / READ / COMPARE commands. ...
Hi,
I was tracking down a bug that resulted in a secure fault exception. To save some time tracking it down I enabled logging in the spm. However this resulted in an escalated...
Hello,
So I am just real confused on how the softdevice programming works via the open_bootloader right now and can't seem to track down the documentation I need to be successful...
I'm running a code based on the ble_app_uart example using the PCA10059 dongle. I have the dongle connecting to a raspberry pi 0 W via BLE and when this runs using a power...
Hello,
at the moment I am working on a project with a nRF52840DK as central and multiple nRF52DKs as peripherals. The code on the central is based on the "ble_app_uart_c...
Do the examples in the SDK folder like ble_nus have their binaries with softdevice already? I'm a newbie in Nordic and using the BLE NUS example with nRF52-DK to learn as...
Hi team,
My customer wants to develop a system with one central, multiple peripherals, each bandwidth is <50kbps, but they want the latency can be as small as possible....
Hello,
I would like to know how can i use SPI on the radio example.
I'm using (programming) the radio example, receiver, for AoA and it's working so far. What i'm trying...
