Only information I can get back for the nPM1304 datasheet from Nordic's website is an html version that's missing all the normal sections you expect in a datasheet. Things...
Enabling CONFIG_USE_SWITCH=y causes usage fault on nRF54L15 with nRF Connect SDK v3.4.0-rc1.
Where it crashes: Context switch on interrupt exit, Zephyr arm-m-switch.c :...
Hello,
I have downloaded the newest Zigbee R23 SDK (v1.3.0).
When I use the feature inside VS Code: "nRF Connect" -> "Create a new board" to create my custom board...
Hi
Currently I'm evaluating the nRF54L15 die temperature sensor. I’ve taken a few measurements and noticed something I don’t quite understand yet. Perhaps someone could...
Hi
We used ALA321C3 like antenna for the chip nRF54L15 , but we have a little probleme that the signal of it is not stable.
So we need your teams to help us.
And we...
I have around 140 BLE Scans per second in my environment. I can see them with a NRF52840 with SDK 17 and with an ESP32 as well.
But when I scan using NCS 3.2.2 I only get...
Dear Sir,
I use the nRf52840 DK (PCA10056) which be a ICE to download FW and 3V DC power supply for my DUT.
the 3Vdc connect to Vdd.
I use the DK 3Vdc be my power supply...
Hello,
Here is some information from my environment :
nRF9160 DK
SIM iBASIS
Country: Suisse
Operator: Swissom AG
roaming mode
Use LTE Link Monitor
I...
Hi,
I want to use tne NRFX SPIM module for reading and writing an external spi flash (at25df011) .
I looked at the example in order to reuse it or base my application...
Hi all,
I'm working on a project in SDK 5 (V17.0.2) on a custom board using a raytac nrf52840 module. IDE is segger embedded studio with a J-Link interface to the hardware...
The device we are using is nRF51822. It uses a bootloader from the Nordic SDK 11.0.0
The boot-loader we are using for the nRF51822 has several blocks of code in the SystemInit...
Hello,
I'd like to enable an instance of SPIM2 master (base address: 40023000) in SDK 17.0.2 for SPI operations. In sdk_config.h, there are two options, NRFX_SPIM2_ENABLED...
I am trying to run the heart_rate_collector.py example in Nordic's pc_ble_driver_py library. When I try to execute the program, I get the following error:
Command used...
Hi!
I'm trying to do the TCP example with the nRF5_SDK_16.0.0_98a08e2, a nrf52840 DK board and a Raspberry Pi 3 B+ as a gateway but I got some problems.
For connecting...
Hi, I'm testing the ICMP example, using a Raspberry and a custom board with a nRF52840. I follow the instructions on the "Connecting devices to the router" found in the infocenter...
hello,
i am using two customised nrf52840 boards and this example https://github.com/NordicPlayground/nRF52-ble-long-range-demo to get the maximum range between two boards...
Hi.
I have NRF52840 with softdevice and GPIO0.7 and 0.27 connected to DALI CLICK and set up and 0.7 - IN, 0.27 OUT. I'm also using TIMER2 for running callback every 104us...
I'm using nRF52832 with an external motion co-processor. As a part of a robust reset strategy, I want to connect a single nRF52 pin to the co-processor's nRST pin to generate...
Hi
I'm using NCS 1.4.0 and SES. If I change the setting in Serial LTE modem to CONFIG_SLM_CONNECT_UART_2 for external MCU connection, I get an error msg from SES: Cannot...
Hello,
I am using "nRF5_SDK_for_Thread_and_Zigbee_v3.1.0_c7c4730" for NCP as well as other thread devices. nrfutil version: 5.2.0 RPI3 image: RaspPi_OT_Border_Router_Demo_v3...
