While including <modem/modem_info.h> as first of the include list I get the following build error:
nrf/include/modem/modem_info.h:298:33: error: unknown type name 'size_t...
I2C on i2c2 (the Arduino header, arduino_i2c , P0.30 SDA / P0.31 SCL) is completely non-functional on two separate, brand-new nRF9151 DK (PCA10171) units. A raw bus scan finds...
We have switched over to the new device tree based partition scheme, and developed custom board files with not-secure variant and mcuboot for ota. OTA was tested using BLE...
We have a product in the field using the NRF9160 and AWS IOT MQTT from NRF Connect SDK 3.1.1. It is always connected when awake (power cycle controlled by an external micro...
Dear support team, on our board we have an nRF54H20 which we connect to an external can transceiver using `can120` node. When the board goes to standby state we want to disable...
Hello,
I am trying to flash and debug a custom board using the Raytac MDBT42Q-512KV2 that uses the nRF52832 module mounted. I tried this using the jlink plus and the nRF52...
I'm having a lot of confusion with using TWI on this chip. I have been running example code that I found in this tutorial nRF5 SDK - Tutorial for Beginners Pt 35 B - TWI ...
devzone.nordicsemi.com/.../nrf-connect-sdk-tutorial---part-1-ncs-v1-4-0 I follow the link above to create a hello world project, which has failed all the time. Here is the...
SDK16.0.0 + Mesh SDK 4.1.0
Help, we have developed our own board with a Fanstel BT840X module. Some of our boards are asserting ("Softdevice assert: 154516:0") and I am...
Hi Nordic,
I'm using nRF52 DK (PCA10040). I tried to copy and paste the project from this default location:
...\nRF5_SDK_17.0.2_d674dde\example\peripheral\twi_sensor ...
Hi,
I managed to compile and run(?) my first two programs for nrf51 dongle on Keil uVision, however while i think they run I cannot make the debugger work and see what they...
Any suggested APIs to setup BLE transmit power in NCS?
the set_tx_power() in the Zephyr example looks not work with nordic softdevice controller.
https://devzone.nordicsemi...
Hello
I am trying to compile a project for nRF25840 on a custom board. Build is succesfull but i am getting a 9mb ro-data on the output which means i cant flash it to...
Hi,
I am facing a problem in storing a 64 bit value to a variable.
some of the calculations which is resulting such a high values like this 4701924420
when i am trying...
Is there any way to use remote provisioning of nrf5 SDK example pb-remote in nrf Connect SDK?
If the answer is no, is the implementation of this feature in nrf Connect SDK...
I'm trying to test out the boot loader using the blinky sample. However if I add the following to prj.conf:
CONFIG_SECURE_BOOT=y
CONFIG_BOOTLOADER_MCUBOOT=y
I'm getting...
"SES > File > Open nRF Connect SDK Project..." does not seem to include a thread aware script for Zephyr. Is there a provided script for this somewhere? If not is there a...
Hello,
I would like to use a single COMP I/O pin to compare the pin voltage to multiple references during run-time.
To do this, I was planning on initializing the COMP...
With SDK For Mesh v5.0.0 the mesh_stack_power_down() was actually implemented but there is a bug that will disabled the proxy permanently.
For some unknown reason the mesh_stack_power_down...
Trying out the Sensor Model supplied with SDK For Mesh v5.0.0 raise a few concerns.
The way sensor_initialize() is made requires all supported PropertyId helper functions...
Hello For my application (which is based on the ble_thread_dyn_mtd_coap_cli example), I would like to be able to send a file (for an update) using bluetooth. To do this, I...
