Hi Nordic Team,
I am trying to implement a secure boot chain on the nRF54L15 DK using NCS v3.4.0 (LTS) with the following configuration:
Board: nrf54l15dk/nrf54l15/cpuapp...
As in subject, psa_aead_finish function generates incorrect tag for AES-GCM when Nordic proprietary library is used.
Works fine with Oberon backend.
Similar problem reported...
Hi, I have a question with regard to the nPM1100 PMIC and entering ship mode (not exiting it).
If I am interpreting the datasheet correctly, the SHPHLD pin must be held...
Hi Nordic Support,
I am facing an issue where the peripheral registers are not visible in the Keil debugger during a debug session. Only the core registers are available...
Hi:
Use nRF54LM20A_DK.
Use ncs 3.1.1.
And this is source code:
The following error occurred:
« *** Booting nRF Connect SDK v3.1.1-e2a97fe2578a *** *** Using Zephyr...
Hello, I use the NCS v3.3.0 (ncs\v3.3.0\nrf\applications\nrf_desktop). Can the desktop dongle connect to two keyboards at the same time? Development boards: two nrf54lm20...
With SDK 3.3.1 I do not get the <inf> logging messages when building the Hello World app unless CONFIG_LOG=y is added to prj.conf.
Perhaps this is left as an exercise for...
I'm transitioning from nRF5 SDK to NCS and using Segger Embedded Studio (SES).
When using nRF5, SES gives options for the Compiler, including saving the Preprocessor output...
Hi,
I'm getting an error while trying to update the modem firmware (mfwnrf9160121.zip) on my thingy91.
I'm using nrfConnect Desktop on Windows 10, I activate DFU mode...
Hi. I am currently using the nRF52840 DK board and using the SDK 17.02.
There is our software engineers who are working on the heart rate service app to modify to suit our...
Hi,
I just got Thingy:91, and I was trying to see the response for a simple hello_world (found in zephyr\samples) application from Thingy:91.
Thingy:91 got programmed...
Hi,
Are LTE-M efficiency/TRP/TIS results of the nRF9160 DK on-board antenna available? In case there are several DK revisions available, does the version affect antenna...
Hi,
I am trying to understand how to enable SPI in blinky application provided by Nordic. My intention is to transfer data between the two Nordic development kit running...
I have advertising in s130 set to BLE_GAP_ADV_TIMEOUT_GENERAL_UNLIMITED. The idea is to advertise until a connection event is received. In reality the user will pull the finger...
Hi ,
1. I learned from Nordic FAE that on the nrf9160 module, 10 minutes after the edrx mode, the nrf9160 module automatically powers off the sim card to save power,
2...
Hello Team,
I want to use scheduler to schedule two tasks i.e task_1 and task_2. The task_1 and task_2 are as follow:
void task_1() { printf("Task 1 ran"); }
void task_2...
Sorry this might be a stupid question.
We are evaluating some modem to develop a IoT device, NRF9160 comes up to our list as its tiny size.
In the design of IoT device...
I wants to use break point in project but when i set break point then 4 or 5 times working after that goes to NRF_BREAKPOINT_COND, I am using nRF52832. so guide me where is...
We are using NRF52840 and we have a watchdog timer connected to reset the Nordic, if needed. What is the minimum and maximum time need to insert a reset on Nordic?
thanks...
I want to transfer sensor data to a raspberry pi using the in-built USB on nrf52840. The example codes have the following classes: CDC_ACM, Audio, HID and Mass storage. I...
