Hello!
I think there is a problem in NCS v3.3.0. nRF54L target, sysbuild build with MCUboot and TF-M, partition layout coming from devicetree (SB_CONFIG_PARTITION_MANAGER...
Hi, I'm developing a keyboard-pcb with NRF52840. I'm doing this as a hobby and are not that experienced with integrated circuits. Anyway, I designed and produced a pcb, but...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
Hi
The TWI driver has a twi_clear_bus() function but the TWIM does not.
I'm getting an I2C error, and need to do I2C soft reset. I'm doing this manually at moment but...
I recently completed a field-upgrade path from an nRF5 SDK 17.1 application (with the legacy Secure DFU bootloader) to a fresh NCS-based firmware stack, while preserving user...
Hello Everyone.
I'm getting falls values on the power profiler, I just connected a 1K resistor across the External DUT and the voltage is 3.6V so expected values should...
Hello Everyone,
I have done I2C communication with Grid Eye sensor (AMG 8832) using twi_master_with_twis_slave (nRF5_SDK_12.3.0_d7731ad) example program. Now i want to transmit...
When I tried to set up my J-Link Flash connection it gave me the message "Unexpected core ID.
First Dev Board R0.5 was normal. and marking of nRF52840 chip was QIAAD0 ,...
Hi,
On nRF52840, we are able to engage APPROTECT by setting NRF_UICR-> APPROTECT to 0. However, writing 0xFF to NRF_UICR-> APPROTECT does not seem to disengage APPROTECT...
If you call nrf_serial_write() once to transmit some data, and before the data from this first call is transmitted, you call nrf_serial_write() again, will the NRF_SERIAL_EVENT_TX_DONE...
Hi Team
I would like to know are there any pic libraries for nrf24l01?
Need to send and receive data from PIC16F1526 to an other PIC MUC via nrf24l01 transceivers.
...
Hi,
My task is to work on NFC , I know the basic working principle of NFC . Here I have seen the nfc uart example .
I would like to transmit the device name, mac address...
Need advice on choice of advertisement flags.
Beacon advertises alert and non alert beacons: On the alert beacons the central is required to connect and respond to the beaconing...
I have looked at and used the following references:
https://devzone.nordicsemi.com/f/nordic-q-a/47484/ble_gap_evt_scan_req_report-not-working
https://devzone.nordicsemi...
Is it possible to implement open thread cli using 16 castellated pins of BT840 ?? I can change the uart pin by rebuilding the open thread libraries ,
Can I avoid using...
Dear all,
In our project we are using "nrf52840" IC is used. We need to check its strength in various physical layer by loading the " Direct mode code ".
We have sucessfully...
Hi !
I need to develop a BLE communication link between a smartphone (Android first, iOS after) and the BL654 Laird platform (based on nRF52840).
I found multiples strategies...
i am developing a bike power meter and designed my own hardware.
From software point of view I used the Ant+ bikepowermeter example from Nordic.
So far my status is, ...
