During my development, I found NRF5 SDK only supports symmetric RX/TX data length settings.
Here is the on_data_length_update_request_evt in nrf_ble_gatt.c file.
static...
This is a product based on nRF52832, which uses BLE Bluetooth to scan iBeacons and communicates with an LTE module via UART for data reporting.
It occasionally enters the...
Hello,
I am working on a project that will require external flash. Is there an example program compatible with the following external flash device?
M95P08-I - Ultra low...
How do I preprocess a C file (typically done by passing the "-E" option to the compiler) in VS Code with nRF Connect SDK 3.0.0 or later? I want to see how a complex macro...
Hey,
the USB connection to my nRF54L15-DK isn't working anymore.
It is not showing up in nRF Connect Desktop and I can't find it under /dev/tty... or /dev/cu...
The...
I am relatively new to embedded and am wondering if there was a "best practices" guide / checklist for production deployment somewhere. Things like making sure you are using...
Hi. I'm trying to write a simple MQTT app. I am consistently getting these KConfig errors to do with variables I'm not using, and I have tried to set CMake to ignore these...
Hi:
I want to send pictures and voice.So it needs to be faster.What should I do?
I use nrf52832/sdk16.If nrf52840 is used, can it reach 2Mpbs?
Measurement example:nRF5_SDK_16...
Hi there,
Here is what I'm trying to do. I'm trying to use the 52832 as a badge to be used by people in order to report the zone the person is in using a ble mesh network...
HI:
My IC: nRF51822QFAA My SDK Project: ...\nRF51_SDK_9.0.0_2e23562\examples\ble_peripheral\ble_app_template\pca10028\s110\arm5_no_packs
Appearance：
When I Powerup or...
Hi, I'm having problems flashing the firmware on my Thingy52. I was recently on a course that used another Nordic Semi dev board to connect to the Thingy52 over I2C and use...
Hi. I want to disconect softdevice and ble in order to access to flash memory. I know there are a lot of ways to deal with it. But i want to test to disconect softdevice and...
Good afternoon, Today we had a question about the certification of our product related to the reliability of communication. We received a letter of the following content:...
Hi,
I am trying to update my advertisement data as well as scan response data (i want to put some custom advertisement data and the device name in scan response data). ...
My three buttons are pressed each time, and the LOG information is as follows
0> [00:00:00.000,000] <info> app_timer: RTC: initialized. 0> [00:00:00.000,000] <info> app...
SDK:15.3.0
CHIP:52832
I downloaded sdk15 for nrf52832.all sample programs and soft devices are working fine but boot loader coding is showing some error. I am using this...
Hello,
I am developing the following application:
An nRF52840 bluetooth module connected to a sensor does data acquisition and then sends it directly to an nRF52840...
Hi,
I am trying to use SPIM3 to drive LCD(ili9486), but I have encountered some problems, hoping to give me a solution.
I have 2 questions:
1. spi_config.dcx_pin
How...
Hello, we have run the power profiler on two different example projects, and want to understand the difference between the two.
When we run the blinky project
nRF5_SDK_16...
I am buys setting up a project on the NRF52 that needs to use the TWI. Usually I would read byte for byte, and if one of the registers has enough data to justify it, I would...
I tested sdk16.0 with secure uart debug example, that DFU needs to enter bootloader twice(press button4 and reset twice), first time to update setting file, second time to...
