Hello,
On nRF52832, I implemented a code with PWM output at P0.07.
Here is the section at my overlay:
pwmleds {
compatible = "pwm-leds" ;
pwm_led0: pwm_led_0 ...
I downloaded the ncs2.6.0 version using Baidu Cloud in the China region, then set the path in Toolchain Manager of NRF Desktop, and Toolchain Manager correctly identified...
Hi,the Nordic team.
I am using nrf54L15 to develop Matter. I have seen that the official sample programs are all equipped with external flash. How can I run Matter programs...
I am using nRF Connect SDK v2.4.0 and an nRF5340 DK set up as a PAwR advertiser. Is it possible to specify the channels to use in the Periodic Advertising train? I found the...
Hello! The PCN 219 rev 1.1 says "The new device revision of nRF54L15-CAAA is not drop-in compatible with the current revision, requiring update to PCB schematic
and layout...
Hello.
Im tring use nrf_dm sample with nRF5340 on nRF Connect SDK V2.9.0, with a custom board.
I got the error when I try dm with other device:
my prj.conf:
...
Hi everyone, I have a question related to the power supply of nRF52840 DK
I want to operate the nRF52840 DK with a LiPo battery (for experimental purposes). Is it possible...
The antenna is mechanically symmetric, but as I understand not electrically symmetric.
Is this an errror ?
www.fractusantennas.com/.../UM_FR01-S4-210.pdf
Chapter 5:...
I am wondering what happens to the NRF LOG statements when not running in the debugger.
I have found (probably due to interaction with the SoftDevice) that too much NRF_DEBUG...
I cannot get the scope of the sdk_config.h file to encompass all modules. Process
Start with example project using the file system as per the install.
After compiling...
I would like to use the UART at the lowest possible level and Ihave created a very simple example which uses the UART bus with the registers. The example should write word...
Radio is flashing green, on and off, but I can't seem to connect to it. Looking at the graph of usage, I can see that it is talking to something since the available amount...
Hi,
I'm using pc-ble-driver-py.
I bought the nrf52832 dongle.
The problem is uart pin number of dongle.
The pins of my dongle and the pins of the hex file are different...
I am working on adding firmware updates to my BLE application on the BL652 module ( nRF52832/PCA10040 ). nRF 15.2.
I added in the code for the BLE Background DFU, which...
Hi ,
I can not understand or there is something wrong in this example here ;
He defined " point_fifo" but initialized "my_fifo" , How does this work ?
https://infocenter...
We want to qualify a product with nrf52832 and preferable S132 6.1.1. When we tried to use QDID 125047 there were inconsistency problems in Launch Studio, table 1a was not...
Can i configure more than one pin for wake up the microcontroler from deep sleep ? like this: nrf_gpio_cfg_sense_input(30, NRF_GPIO_PIN_NOPULL, NRF_GPIO_PIN_SENSE_LOW); nrf_gpio_cfg_sense_input...
What is the receive buffer size for IP packet data, i.e. how many bytes of data can the modem receive (in one or several UDP packets) before I call recv() or recvfrom() on...
Hi Sir,
For test the nRF9160 GPS, based on the nRF connect v1.2.0.
Do we have the GPS API for cold/warm/hot start?
And which example code we can reference?
Thank you...
Hi,
Recently I have been working on serial LTE modem code and it seems to work great for TCP and UDP. I am trying to enable GPS module by the command mentioned in this link...
Hi,
is the 100k pull-down on the COEX2 pin required as stated in the product specification ? I don't see it being followed anywhere (reference circuitry, nRF9160 DK schematic...
