Nordic Support,
My product uses the nRF52840 chip and nRF52 SDK 17.1. I have a feature request to support hosting multiple peripheral connections, each with a unique advertising...
I am working with NRF52840 with SoftDevice S140 and SDK v17.1.0.
The boot loader address for this chip is 0xF8000. I can set up one of the 'fstorage' module with the address...
Hey everyone,
Does anyone here have experience with firmware OTA updates over the JIO NB-IoT network? The process seems a bit different since JIO Cloud always sits between...
Hello:
The latest nRF54L15 Errata for Rev 2 shows that the previously reported "GPIOs can exhibit radiated emissions" is no longer present in the Rev 2 SoC.
Can you please...
Hi, this is a very broad issue that i am having, because i dont know the source of it. I am simply unable to use the bme68x IAQ library. i have downloaded the external bsec...
Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
To the kind attention of Nordic support team,
we are very much interested in interacting with your nRF52840 devices preprogrammed with the wireless bootloader and waiting...
Hi! We are currently trying to develop a low power framework for our nRF52840 DK with SoftDevice S140. After disabling various peripherals and interrupts we use the provided...
Hello Team,
I just recently purchased Thingy52 i was wondering i can use NFC NDEF update using python library if it is possible can you point me to right
documentation...
Hello!
I am working on firmware for device that has freertos in the base and implements BLE beacon and 1 service with 7 characteristics. Everything works. But power consumption...
Hi,
We are currently testing DFU upgrades on Android. In my current setup I have two different phones, a Sony one running Android 8 and a OnePlus running Android 10.
The...
We have a device (in central mode) initiating a secure connection to a peripheral (slave) via the usage of `pm_conn_secure(conn_handle, false)`. This results in a `PM_EVT_CONN_SEC_SUCCEEDED...
Hi All,
I want to convert analog input into digital using SAADC on nRF52840 DK. After that to push the SAADC output through the Bluetooth (nRF connect bluetooth mobile application...
Hi，
Recently，i try to install the tool chain of nrf connect sdk as the instruction as guide。After installed west，then run command “west update”，but got an error：
Can...
Hi ... folks
I am using nRF52832 and analog IR sensor , Working with the example saadc . In this case , i am giving the IR sensor input voltage as 5v , analog pin 2 .I am...
Hi,
I am using NRF52832 Development board, SDK(nRF5_SDK_15.3.0_59ac345) from this i am using (/nRF5_SDK_15.3.0_59ac345 (4)/examples/ble_peripheral/ble_app_uart) example...
Is the nRF52 RSSI block of the RADIO module based on the entire 2.4GHz ISM band, or can it be configured to only measure a given 1-2MHz band of interest? According to the...
I'm using the serial library for the first time. What are the advantages/disadvantages of using IRQ and DMA? How should FIFO queue and buffer sizes be chosen?
Hi,
I am using the following code to implement a millisecond timer read function. In main, while loop, I do nothing but run a 1ms delay and measure the time in mill second...
Hello, I'm a researcher.
I wanna use Bluetooth CTE(Constant Tone Extension) feature with 1-antenna TX + 1-antenna RX.
I have seen some articles that nRF52840 DK does...
I am using nRF52832 with SDK 16.0.0. I have a simple application that uses SAADC and BLE. It reads values from three channels AIN0, AIN2 and AIN4 and sends them via BLE every...
