Hi,
When i want to connect my Power profiler kit II to my laptop, it first blinks GREEN. After i connect to it using the power profiler app, it goes: RED -> AMP (Ampere...
I have a custom board with a nRF5340 and need to configure VREGH in DC-DC mode and set 3.0V output on it.
I see the documentation on REGULATORS — Regulator control where...
Hi,
NRF54L15, nordic sdk version 2.9.1
I recently lost ability to build my application. I get this linker error:
/home/adam/ncs/toolchains/b77d8c1312/opt/zephyr-sdk...
Hello,
Now, I currently run Asset_Tracker_Template on Thingy91X
https://github.com/nrfconnect/Asset-Tracker-Template/blob/main/docs/common/getting_started.md.
And, I...
Hi,
I have autoprovisioned and autoconfigured my nrf52840 board (provisioning and configuring are made inside the software and not through external app/provisioner).
In...
Hello Nordic Team,
Currently, we are performing power consumption testing using the Nordic nRF54L15-DK development kit.
As part of this, I aim to fully disable the Radio...
Good afternoon we are updating some Nordic chips but to make the connection work it is necessary to install the modem version 1.3.1 wait for it to connect and then install...
Hi everyone,
We are investigating whether the nRF52840 can be used to carry out USB device negotiation with a host in terms of setting the maximum charging current.
Our...
I'm using the ble_app_uart as my template for Bluetooth and UART communication. I'm on SDK 15.3.0, Segger Embedded Studio and nRF52840.
I would like to send the information...
Hello,
We are facing an issue where we are having a lot of packet loss (UART nrf52832) on two sensors connected to an Android Application (Android Pie 9.0). The tablet model...
Hi!
I'm trying to implement a traditional ring buffer with the nrf_ringbuf library. I'm using nRF52840 DK with SDK 15.3.0 and SES.
I'm going to receive strings of data...
Hi all,
I am working with Thread SDK v3.1.
When I run mqttsn-client-public and subcribe to make MQTT-SN network use UDP. But it doesn't have DLTS.
In the topic : https...
Initiated west init as per nRF Connect v3.0.0 Getting Started Assistant but resulted into an error. Worked the last time I did this. Any idea what's going on? "west init ...
Hi,
I'm trying upload firmware onto the nRF24LU1+ dongle (nrf2728) from the nrfgo motherboard (nrf6310) through nrfgo studios. I have it hooked up just as described in the...
Hi,
With my mistake, the firmware in nrf52840 Dongle is none, Do you know how to get the official firmware? and how to download this firmware? if using Jlink, any pin support...
Hi All,
I have a scanner project based on nrf52840 + S140 and I saw S140 (7.0.0) seems to support nrf52811.
So I want to port existing project to nrf52811 + S140 7.0.0...
Hi, I am experiencing the nrf52832 with some testing and developing few examples.
I am using nrf5_SDK_15.3 SES. OS : Windows 10.
I am using nRF52832 only. I have seen...
When designing an NFC coil to use with the nRF32832, are there any recommendations as to the coil inductance and Q that we should target?
Being a passive design, we are...
Hi I am using the tutorial from https://github.com/bjornspockeli/custom_ble_service_example . I have uncommented some of the starter code from ble_cus.c. My understanding...
I am inquiring about something I know very little about but will try to communicate for the information. Smart phone applications can be opened through a QR code which utilizes...
Hi,
We are using ncs tag v1.0.0.
I am using i2c_scanner example firmware. It works find when used as it is.
When I added "UART2" in this firmware i am getting hard fault...
