board : nRF5340
sdk-nrf : v2.7.99-cs2
Zephyr version: 3.6.99
I am following https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/app_dev/bootloaders_dfu/qspi_xip_split_image...
Hello Team,
We are working on custom board using nrf54l15 platform.
If we flash only application code, it works, LED is blinking & BLE advertises. But after adding DFU...
Hello!
I'm currently working with the nRF7002 Wi-Fi chip on a custom board. The MCU used is STM32H573ZIT6, and the software is Zephyr 4.0, specifically using the Wi-Fi shell...
i have PMIC(I2C based )Max20360 that is developed using twi sensor , to this when i am intergrating a SAADC part throws error error # 134 :expected a field name . 1)why am...
Hi, when I am trying to set up channel sounding, I am looking for the best parameters for CS configuration. The main problem I have is that even with slow movement (1 km/h...
Dear sir,
I'm using the sample application "channel_sounding_ras_initiator" to performing the evaluation. Here are my test environment: - Developement kit: nRF45L151 - Tool...
Hello,
I previously used DECT NR+ modem firmware mfw-nr+_nrf91x1_1.0.2 on nRF9151 DK Development kit and moved on using the new modem firmware mfw-nr+_nrf91x1_1.1.0.
But...
I am using UART with interupt on a project where I communicate over RS-232 with an external circuit. This circuit keep TX low until it has received a reset command from the...
Hi,
I'm beginner here.
Could you guide me how to check that my nrf9160 custom board is working?
Should I program it with any firmware before programming with my application...
Hi,
I have merged nrfx_spi and ble_app_uart examples. I am working with SDK15.3 on a nRF52832 based ISP1507. I seem to be able to transmit the data stored in the tx buffer...
hi ,
i am trying to make a project based on detection using ble 5 on raspberry pi 3.
plz help me with selecting correct and most appropriate ble 5 dongle for good range...
Hello, Dear Support. I try to build BLE Mesh from several nRF52840 Development Kits. I use example [serial] from SDK for Mesh v3.1.0. After building solution in SeS and starting...
Hello:
I am able to compile, load/flash successfully for my BLE + FreeRTOS application to my nRF52840 DK board. However, I am not able to start or pause execution of the...
Hello.
I am trying to migrate from sdk 11 to sdk 12 and I am having difficulty in adapting the device_manager.h functions that I am using in my code to the peer_manager...
Hi
I would like to be able to (force) stop characteristic notifications at some point in time.
Imagine a smartphone connects to peripheral and enables characteristic notification...
Hello,
I wanted to test the range of long range bluetooth using two nRF52840 USB dongles with the blinky example firmware of the nordic SDK 15.3 combined with softdevice...
Hello,
I am using nRF52832 DK PCA10040 v1.2.4, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
I have very basic query...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
RESETREAS will give cause of reset. But for...
Dear Team
I use the Lwip_mqtt_publisher example from the SDK 15.3 with a PCA10056 board.
Also, I used an Ubuntu 18 Instance(IPv4, I used 6tunnel) to run the Mosquitto...
Hello sir ,
I have conneccted an BLE400 dev kit to an swc J-flash device. And i can't erase it.
Tried with nRFgo Studio on windows 10 an with linux nrf cmd line...
Hello,
I am using the chip nrf52840. I am trying to configure three pins (P0.09, P0.10 and P0.11) as output pins and I am trying to make set and reset functions for them...
