While trying to run the FOTA-TEST upgrades from I came across unexpected behavior when the same script fails twice in a row. I first attempt to trigger a FOTA with the following...
Quoted from Heidi’s blog post Target Wake Time on the nRF7002 DK , published 23 Feb 2023 (available at https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/target...
I have nrf52840 DK board, running cutom image that implements BLE central, constantly scanning on coded (S8) phy. Trying to add NFC T2T tag, and it doesn't work. Disabling...
Hi,
We produced the first batch of 10 modules in July 2026. Out of these, 8 modules are working properly, while 2 are not working.
We then produced a second batch of 10...
Title: SoftDevice Controller: 100% connection establishment failure (HCI 0x3E) with SKY66112-11 PA active
Hi Everyone,
I am working on the following development project...
Hello,
I would like to use spi to connect to a ADC on a nrf54l15dk at high speed using DMA.
I want to use nrfconnect bare metal, but cannot find a starting example.
...
Hello,
My previous question is this.
I try to implement sample application with Radio Driver 1.1.0 to SDK15.0.0 ble peripheral uart example.
Symptom
For few micro...
Hi:
I am fairly new to Nordic so please excuse my ignorance. I recently took over a project which used sdk 11 and I am in the process of updating it to 15 and want to see...
Hello,
We are developing a wearable device with NRF52 as a Beacon with CR2032 coin cell battery. We need to measure current profile for the beacon and calculate corresponding...
My environment is:
SDK14.1 + SD132 V5.0 + NRF52832
2 sensors(MPU9250 + LPS22HB) 1 battery gas meter (LTC2942) are mounted on TWI ( +1mA)
SPI to spi flash. (+1mA) and...
Hi，
I use SDK is nRF5_SDK_15.0.0_a53641a
【1】In examples proprietary_rf , Here is only the example of pca10040 , So I have to download a lower version of the SDK ?
（...
Hello, I am trying to setup and use the nRF sniffer (ble-sniffer_win_1.0.1) on my NRF51DK (PCA10028) board. I followed the instructions and using nRF studio, I erased all...
Hello!
I'm currently trying to lessen the current consumption of the nrf8001.
I tried to change the connection interval, slave latency, and the timeout using ChangeTimingRequest...
Hi,
I've been using the nRF24l01+ for some time now and am quite satisfied. I'm having a new issue that I'm unable to explain and for which I would greatly appreciate some...
I have filed an issue related to HCI UART sample from zephyr running on nrf52832. I compiled the hci_uart sample successfully, but I am not able to use the UART interface...
Hello, I'm using SDK 15 and softdevice 6.0.
I use the micro as a master and I connected an i2c sensor as slave. I had put external 10 Kohm pull-ups, but I had a low level...
Hello ,
I am using SDK for mesh, I have saved .hex image file in flash.
Is there any example or any suggestion how can I run bootloader which will read data from flash...
HI:
Always error while porting,Error: L6218E: Undefined symbol app_uart_init (referred from main.o).
I added a path, and ENABLE UART_ENABLE 1 in sdk_cofig.h
Compile...
I have set up the gcc toolchain on Mac OSX to compile my BLE nRF51822 code and I tried to flash the code. Here are the 3 scenarios that I have tried (JlinkExe on Mac)
Case...
Hi,
I am not sure if this is the right place to open up a thread about a zephyr HCI firmware issue. Since Nordic also contributes to zephyr I'm putting up this question...
