Hello, I want to build serial_lte_modem sample for a custom board based on nRF9151, but it fails with this error:
error: Aborting due to Kconfig warnings
I can build...
Hi, I'd like to evaluate Linux device driver for nRF7002; refer to 315431 , I'd found this requirement had been reported one and half year ago; based on 315431 , I have a...
Hi,
I'm using the nRF52832 with SDK version 17.0.1 , and I'm experiencing an issue with NFC handling .
Sometimes, the NFC interrupt triggers two FIELD_OFF or two FIELD_ON...
Hi Nordic team,
This is a compatibility test. case1 okay: 1,Connect the nRF5340BIS headset with the phone. 2,NRF5340 broadcast can be found on the mobile phone. 3,When you...
first i change to my kconfig file add this
source "samples/subsys/usb/common/Kconfig.sample_usbd"
source "Kconfig.zephyr
second I add to cmakelits
include...
The BCLK_CONT option to i2s_configure() is not being honored anywhere. How do I get BCLK to output continuously without having to do i2s_write() or i2s_read() calls over and...
NRF52840
S140
App based on ble_app_multilink_central.
I have tried to build a bridge between BLE peripheral and PC.
I have spend so many time on PC side app.
The...
This is the Energy Profile that is shown for the nRF82832 and I am wondering about the RX/ switch parts. I assume these RX phases are for receiving scan requests?
What happens...
Hi,
I have a question regarding DTM in nRF5 SDK v14.2.0.
From what I understand Nordic is making use of the payload type '11' = Vendor Specific and is using the length parameter...
if flash nrf52832_xxaa.hex , board start to blinky
if flash s132_nrf52_5.0.0_softdevice.hex, board seems dead
what happed after flash these two hex files
does these...
Hi Folks,
I am playing with uart ble example described in this link ( devzone.nordicsemi.com/.../).
However, I would like to disable encryption on BLE link. I was trying...
Hi,
I have installed Software backend (micro-ecc) as given in:
infocenter.nordicsemi.com/index.jsp
Compiled example: experimental/ble_app_multirole_lesc --> compilation...
I want to make a BLE peripheral device that only allows connections from authorized mobile apps, and an app that only allows connections from authorized BLE devices. What...
Hi all,
I'm having problem porting some project from Keil to SES since our project use absolute memory location to put some variable that will be share between main application...
Hi,nordics
I failed to find primary service successfully .The sdk version is 10.00 and I reffered to the example is ble_app_uart_c_s120.The pripheral is a gamepad .I can...
Hello there,
I was wondering if there's a known issues page fro SDK 14.0.0 (not alpha).
Issue #1: crypto compile error:
I ran into an issue compiling nrf_crypto.c
...
Hi everyone,
Does anyone have the beginner tutorials about BLE migrated to SDK 14?
I am specially interested in those about services and characteristics:
devzone...
what command did "nRF Connect" do, after I click "YES" ???
Im stranded in this example : “ble_app_alert_notification”
I don't know how to use "nRF Connect"
when I...
Hey Dev Zone!
I'm attempting to flash FW onto the Thingy via the nrf52840 dev board (which includes JLink). I connected P19 header on nrf52840 to P9 on the Thingy. I downloaded...
I am trying to run below 10 uA with code below while GPIO and uart are on. Sleep mode is applied (below 10 uA), and only wakes up when button is pressed (can be higher amps...
I have a micro connected to the PCA10040. I can use flow control with 5=rts, 6=tx, 7=cts, 8=rx.
Are these pins necessary or advisable for hwfc?
thanks,
Richard
Hello,
I'm having problems getting a stable channel from an Android device (LG K8) and the nRF52 development board. It is hard to tell whether which side is causing the...
