Hi,
We are running into a serious issue with OTA. Specifically, we have observed that nRF52832 will not be able to perform OTA to a newer firmware given that it is previously...
Hi all,
I'm trying to characterize the UDP throughput of a Thread network consisting of nRF5340 DK devices. I saw that Espressif made a test report and they seemed to use...
I’m using a custom PCB based on the Minew ME54BS01 module (nRF54L15 SoC) for both ends of our proof‑of‑concept: one node as a GATT‑based Channel‑Sounding reflector (leveraging...
Dear DevZone support,
I'm currently evaluating nPM1300 for Lithium Polymer battery management and charging and would like to ask a question.
I understand that I can...
Hi Nordic：
We are currently testing Zigbee on the nRF54L15 platform using the Zigbee R23-add-on-V1.0.0 SDK. It has been observed that when a low-power node disconnects from...
Hello, I am using ISP1907 which has NRF52833. I get the IQ data and configuration from serial as: DF_BEGIN ['IQ', 0, 0, 11, -9, -213] ['IQ', 1, 8, 11, -209, 23] ['IQ', 2,...
I have 2x Power Profiler Kit II up and running using the Power Profiler app - started twice and with separate PPK2 instances selected, as described in another support post...
this time i have some encryption related questions to ask.
I use the "BLE_GAP_CONN_SEC_MODE_SET_XXX" to enble link encryption, doese this correct?
can i set the encryption...
Quick question regarding the boot process of the nrf51822. If a bootloader address is written to 0x10001014, will the bootloader code always be executed, regardless of whether...
Hi
I am using ble_app_hrs for my application.
in this case ble has highest priority , next gpio then timer.
if i send continuous data over ble, by using function...
Hello Nordic expert,
In nRF51822_PS_v1_3, the max bit rates for SPI master is 8Mbps(section 8.8, page43).
But in nRF51822_PS_v2.0, the max bit rates for SPI master change...
I heared a rumour that the NRF581922 will be withdrawn and an other solution will become available. We have planned the 581922 for implementation and want te release the product...
/* YOUR_JOB: Use an appearance value matching the application's use case.
err_code = sd_ble_gap_appearance_set(BLE_APPEARANCE_);
APP_ERROR_CHECK(err_code); */
Shoult...
Do I still have to call sd_ble_gatts_value_set() on the characteristic handle [using whatever temporary buffer I would have been using anyway for BLE_GATTS_VLOC_STACK]?
...
Hi,
I would like to use the app_gpiote files from Nordic in combination with the softdevice enabled.
In the app_gpiote.c file interrupts are enabled using the standard...
As far as I can see buttons_init() initializes GPIO and sets up button_event_handler().
button_event_handler() calls ble_lbs_on_button_change() and always set static uint8_t...
I have problems with my iPad to catch data coming from key presses of HID keyboard profile. First, I programmed the dev tool nRF6310+PCA10005 with the HID keyboard profile...
I installed nrfgostudio_win-64_1.15.1_installer, nrfgo_sdk_2.3.0_setup and nrfprobe_v2_0_0_7252 to test nRFgo starter kit(nRF6700). I tried to test uart on nRF24LE1D. but...
I want to establish a link between two nRF8001 devices. Is there an example of how to do it? I am using micro controller on our application board to control the nRF8001 devices...
Dear Developer Zone,
At this time, it is possible to upgrade the firmware version using Bootloader. But, is there any way or any plan to upgrade also the softdevice version...
