Developing an implementation for UltraWideBandImpl for a different UWB hardware solution (not the provided qm35 implementation) and running into integration problems
The...
HI, Good day to you. we kindly request your confirmation of the COF ( Country OF fabrication) origin for the NRF52810-QFAA-R component. We would be most grateful. the label...
Hi, We're in the product validation stage of development with nRF54L15, part of the validation is temperature cycling, we noticed that devices seem to be "stuck" in sleep...
Hi,
I am trying to configure an Xiao Seeed Studio nrf54l15 sense to transmit pre-processed sensor data via BLE extended advertisements. As the payload is more than 251 bytes...
In this post mentioned: "Maximum theoretical peak data rate is 3.4 Mbps when transmission is scheduled into packets of 4 slots using MCS4, and these 4 slot packets are transmitted...
I want to use a new source LF clock to raise the precision from +-250ppm to around +-20ppm. I already have an oscillator mounted in my PCB, so I want to use it for BLE. I...
Hi,
I would like to know if its possible to run Azure FOTA functionality w/o using Partition Manager (aka `SB_CONFIG_PARTITION_MANAGER=n`) ?
Trying to build this gets...
I try to optmize my code so it can run on the 128k chip.
My issue is with pstorage: I have 7 variables (from 4 bytes to 20 bytes) that I store in individual blocks. But it...
I have the nRF51 Dongle and an nRF51822 BLuetooth Smart Beacon kit. For software tools I have IAR's EWARM 6.7 for a complete IDE or command line GCC/GDB.
Are there any...
Hello,
my idea is to turn on a GPIO-Pin of the NRF51822-Beacon-Kit when my smartphone found the beacon. Of course if the smartphone is out of range or far away the pin...
Hi all,
I am trying to figure out how to change the LEDs blink rate on the go.
I have set up the timers_init() and let say every 500ms sensor data is read on dev kit...
I want to make sure I'm far from ever having a stack overflow event. Is there a way in the IDE or elsewhere to monitor this risk? The map file produced after a build?
Hi,
I'm trying to get the actual connection interval used between my nRF51822 device and iOS device.
I have read this article , but I cannot get it worked.
I used sd_ble_gap_ppcp_get...
Hi,
I want to disable the softdevice (S110) in order to use the "flash_page_erase" and "flash_word_write" functions. But, when the sd_softdevice_disable() is called I get...
Hidden in the guts of this answer is:
Please be noted that not all central
stack have full support to
automatically discovery secondary
services (e.g S120 stack)...
In the code for the bootloader in dfu_dual_bank.c and the function dfu_init , I currently get an error code on timer start: 4 ( NRF_ERROR_NO_MEM ).
err_code = app_timer_start...
The device name is set in the usual way at the start of gap_params_init():
BLE_GAP_CONN_SEC_MODE_SET_OPEN(&sec_mode);
err_code = sd_ble_gap_device_name_set(&sec_mode,...
Hello,
I am new to BLE profile development. I searched in web but could not find out a useful guide for this in terms of actual implementation(coding). It is seen that all...
Why is the "old" EK "not recommended for new designs"? Will the old EK work with the IOT SDK?
(Maybe it is chip rev dependent? I don't have the my EK on hand so I don't...
Hello,
I have purchased a Intel Galileo Gen2 (x86 Arduino) and RedBear BLE shield v2.0. The Arduino IDE I use is Intel's version. I have imported the corresponding libraries...
The application uses bsp_button_is_pressed() but this device has no buttons. This results in err_code set to NRF_ERROR_INVALID_PARAM and subsequently a system reset during...
As previously reported for SDK 7.0.1 here , the documentation for SDK 7.1.0 in:
API Reference/nRF51 SDK/Peripheral Drivers/GPIO and GPIOTE
is missing all info about...
