Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
I'm following the heart rate sensor example in the VS Code Youtube Tutorials series, and there are some pretty straightforward prinkt statements in main.c, such as 'Bluetooth...
I'm getting data from peripherals, and I need 96KB/S to get to the NET layer, because the other side needs to use data in real time, but the data transfer is too slow.
So...
I have been working with multi-sensor example of ZigBee to develop it in zephyr. every things went well of endpoint sensor except that the coordinator suppose to receive the...
Hi,
I am facing issue at ble_stack_init() which internally calls sd_softdevice_enable(). I get NRF_ERROR_SVC_HANDLER_MISSING at sd_softdevice_enable() return value.
...
Hi,
i use the nRF5 SDK for Thread and Zigbee v4.1.0 , the s140 an the ble_thread_dyn_proximity - example.
I want to use the LESC encryption of BLE (in addition to Thread...
Can anyone help me with this:
I'm trying out the 'threads' sample under Visual Studio 1.8.0. Not having much luck. I'm a newbie and have followed the Video tutorials to...
Hi,
I am currently using an audio board utilizing the nRF5340 MCU. I would like to enable the BT_SHELL to use the Bluetooth command Shell, may I know how I can achieve that...
Hi,
I'm trying to measure the power consumption of Zephyr's iBeacon sample (zephyr/samples/bluetooth/ibeacon) on the nRF52840 DK. I prepared the DK by cutting the PCB track...
I use nRF52840_QIAA for design, now I need to provide ROSH of this model, I found it on the official website, please help to provide it, thank you very much!
Hi all,
After Licence request I got email with Key.
Segger Embedded Studio 4.12 accepted this key but SUA expiration date is not valid, there is just red cross and no...
Dear ,
I'm using nRF52832 to do some 2.4G communation without softdevice. Now i need to update firmware with mybootloader.
Is there some mathod to do the vector table...
Dear Team,
I am working on real time clock with the help of : github.com/.../nrf5-calendar-example but in this when do the power on and off so again start from starting...
As a continuation of Case ID: 282083 “merge cdc-acm support and BLE service”
Thanks to your support the merge was successful : both functions (cdc-acm console and led and...
I am developing a solution using the NRF9160. The device is successfully reporting to my server using a blend of the Location and HTTPS samples. I would like to operate under...
Hi, i have been converting my keil uVision 5 project to SES. Attached font file works fine in keil but not in SES. Everything else work great as expected. But not the font...
