Developing on the nrf51822
Have working code for the nRF52840 Dongle using the pc-ble-driver therefore all Bluetooth work is done using sd_* calls. The PC provides easy...
Hi ,
I would like to know if a matching network is needed if I am only using a single external flex antenna for both LTE and GPS using a RF switch between them and a uFL...
I am a student interested in Nordic.
My coding skills are very poor.
So I want to get help.
I want to use the vl53l1x sensor in nrf52. (My ultimate goal is to measure...
I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
hi,
we use the NFC Tag Type 4 of nRF52833, it can be listened to by mobile apps and read or writed by apps. But when we use NFC reader to listen this tag, the card reader...
Hello!
I'm in the process of prototyping a PCBA that is Battery Powered with VDDH (Tied to VDD for now), but also has the option of USB Power.
When USB Power is active...
Hi,
I understand 'nRF Sniffer for 802.15.4' is typically used with nRF52840 DK or nRF52840 Dongle.
Would it be possible to use it with nRF52833-DK instead? If so, any...
SD: s132_nrf52_7.2.0_softdevice
SDK:nRF5_SDK_17.0.2_d674dde
I was running the firmware with debug mode. It only has an application timer and Bluetooth. I feel it might...
Dear Sir/Madam,
While I did take a course in Bluetooth I am still a beginner.
I know some boards have HID "support" (RN42 for example) I find it hard to believe that it...
Hi, Recently I bought the nRF9160DK for development and during get start i am facing some issues
for get starting i am use this video as reference https://www.youtube.com...
Hi all, I am using Arduino nano 3.3 BLE in my project. I am using light_lightness server as the program for the nano boards.
However, I found a difference in the transmission...
Hi everyone,
I want to sample eight analog sensors connected on P0.30 through a multiplexer. I created an app_timer that expires every 10ms. When the timer expires I start...
https://devzone.nordicsemi.com/f/nordic-q-a/82644/nrf52832-freertos-ble_app_hrs_freertos-lowpower
I mentioned the above problem before. After your support, I found that...
Hello everyone,
my application is build based on the mulitrole example. The device name is somehow limited to 4 letters.
I checked:
init.advdata.name_type = BLE_ADVDATA_FULL_NAME...
Hello, I attempted to enable the zephyr task watchdog model but whenever I configure it to enable the hardware watchdog module I get the error above. Any idea why I am getting...
Board: NRF52840
SDK: 16
Soft Device: s113
So our board is custom and does not contain a crystal. We are treating P0.00 and P0.01 as GPIOs for button inputs. P0.01 works...
Hi all,
I was able to create a mesh network with two nrf5340 boards configured with the mesh light sample and the mesh light switch sample.
I am trying to substitute...
Using SDK15.3 on 52840. I've got a UART set up talking to something at 9600 baud..
The short course here is that imediately after init, I get an IRQ with a NRF_SERIAL_EVENT_DRV_ERR...
Hello, I´m working on my audio project and I try to stream some audio data (currently a 1 kHz square wave signal with 3.3 V peak) over I2S. The audio signal is sampled by...
