Hi,
Again the topic which has already been discussed several times in this forum. I just want to share my experience and perhaps help other users having difficulties.
...
EDIT: We found the reason for this and it is a hardware issue. This question can be deleted as it is no longer valid.
-----
Hello,
We are currently developing a...
Hello,
I would like to obtain some information on the possible substitutes for the nRF51822 (BGA Packaging).
I received notification that right now only the final orders...
I am using the nrf9160 for an OTA firmware update application. I initially executed the fota download file from the http_application_update sample project in it's default...
Hello Team,
Could you please share some sample application or procedure to handle power modes (Sleep, Deep Sleep, etc) of the nrf9160.
Please let me know.
Regards, ...
HI Nordic support team.
I have a question relate to RSSI in proprietary_rf application.
We test on esb_low_power_ptx.
Can i read RSSI of esb_low_power_ptx?
thanks...
Hi. I'm using NCS V2.6.1 with nrf52833, and I'm trying to merge the “zephyr\samples\bluetooth\iso_connected_benchmark” sample application with the “nrf\samples\mpsl\timeslot...
Hi Nordic support team.
I incharg project replace NRF24l01 by new design with nrf52833.
Using nRF5_SDK_17.0.2 and segger studio compiler.
I using esb_tx example, the...
Nordic DFU SDK version 2.5.0. Github issue here .
When the Android screen is off, the DFU fails right after starting. This appears to be because the scanner cannot find...
Hi, I have a project using the chip nRF52832 and sdk nRF5 14.2, I'm updating the firmware to use the nRF Connect SDK 2.2(NCS).
In my project, i use spi0 and spi2, so a can...
Hi.
I start SPI as well as I2C at the same time . then build code , the build error is occur . below is error code .
The SPI and I2C cannot be used at...
Hello,
I try to building sample code nrf_dm for nrf5340DK, but I got failed massage:
.7.0-rc2/nrf/subsys/dm/dm.c.obj -c C:/ncs/v2.7.0-rc2/nrf/subsys/dm/dm.c C:/ncs/v2...
Good Morning
Im using Zephyr, SDK2.6, toolchain 2.6. the peripheral_uart example is flashed to a 52840DK. when I connect with my phone IOS NRF_connect I get the error
...
I run the LWM2M client and send the data to the server. Nrf7002dk connects to the internet via wifi. Now I would like to update the software but I can't seem to do it. The...
Hi, I want to implement OpenThread features with another sample and I'm not sure how to go about it. Is it even a good idea to add OpenThread to another sample or is it better...
I use the serial port routine SDK17.1, nRF52833 want to burn the protocol stack, s113_nrf52_7.2.0_softdevice. But when I burn it to the chip, the address is 0x1000 and if...
Hello I have a board that I am trying to profile with the power profiler kit 2 and the readings seem very wild. I have a device that I know the base configuration with the...
I have a customized PCB with nrf52840. Pin 0.18 is used as CS pin in SPI communication.
I want to disable the nreset function and I add this CONFIG_GPIO_AS_PINRESET=n in...
I'm using the CLI interface through USB and UART, and I am wondering if there are any innate methods for checking the validity of the data being sent and received via the...
hi Nordic support team,
I cannot re-flash firmware for nrf52840 after ram off is implemented.
I recheck with other chip like nrf52833, it have the same result: \althrough...
