I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Our board is based on nRF52833, using SDK 2.1.2, Zephyr 3.1.99 Project is configured to enter low power mode for both CPU and peripherals CONFIG_PM=y CONFIG_PM_DEVICE=y Our...
Hi,
After downloading any of the projects from nordic github, how does one compile the project successfully? Where should i extract the files to and what paths should i...
HI.
NRF connect For Desktop Programmer program Fail.
So I used command Tool (nrfjprog). command Tool worked.
Enviroment:
- nRF Connect For Destop v5.1.0
- Programmer...
We're attempting to provision one of our nRF9160-based IoT devices to our AWS VPC.
We're following this procedure:
Provisioning our eDude on AWS
Step 1: Provision the...
I'm trying to get FOTA updates working on the NRF54L15 DK. I noticed there isn't a dedicated guide available for these yet so have been using this page: https://docs.nordicsemi...
I’m encountering a build issue with Zephyr (version 3.7.99) on my custom board based on the nRF52840 SoC. The build process fails during the linking stage with an undefined...
Hi ,
We are using MCU nRF52832-QFAA-R (Flash 512KB & RAM 64KB) with softdevice s132 - 6.0.0.
I am not sure what is extracly Soc Revision of the MCU ? But I read some information...
I have a custom SMP handler that uses an SPI transport. If I use the pin reset to reset the module after programming sometimes the module hangs when calling that handler....
Hi We would like to use the nRF5340 with a custom network core image that runs the full Bluetooth stack and I have gotten it to work with sysbuild. However, we would like...
Hi, I am having problem making DFU work on nrf52832 using nrf connect sdk 2.6.0. Below is my mcuboot.conf under child_image and prj.conf. Please guide me where I am wrong...
Hello,
I'm trying to reduce the range of transmission of the nRF5340 SoC for an Auracast Broadcast. I would like it to be detectable only from a distance of 1 or 2 meters...
Hi,
We are using nRF52832 for BLE application.
In our custom device we have loaded the firmware and it is working in debug mode.
But once we remove the SWD cables...
Hi guys,
I'm working on this project which was basically a migration from STM32 to the nordic NRF52832 in order to enable the BLE beaconing mode.
It has been a challenge...
Hi everybody!
I'm starting to study nrf9160. Work in SEEGER Embedded Studio. And I immediately had a question:
By default, it is created C project, But I want to create...
Dear nRF experts. We use the sample code of radio_test as the production test program. We directly add a UART command. When the user enters this command, it will enter sleep...
