Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hello,when i get connected to the phone,when i call err_code = ble_hts_measurement_send(&m_hts, &simulated_meas) and err_code = ble_bas_battery_level_update(&m_bas, battery_level...
I got the Dynastream N5 kit and have successfully used it with limited ANT work and was trying to get BLE working but can't get a driver for the USB dongle. On the 51422 product...
Hello,
I am looking to send packets of real time accelerometer data over uart to my PC via uart. The packets are similar to the code shown below where the data array is...
This is really bad, I downloaded the latest 1.7.0 SDK to the machine and could not build any application (including examples) Always appear errors
Create a GPS.Emproject...
Hi,
I have nRF9160 DK:
PCA10090 v0.8.3
modem firmware 1.2.3
The specifications says that the minimum consumption current is 7µA. So I flash a hex file which shuts...
(Using nRF Connect SDK 1.5)
I have the setup so far that partition manager is aware of the external flash and creates a single partition for it. The documentation section...
Hi nordic
I am using 52832 with sdk15.3:
when I program the hex with sd+APP+bootload, it works fine, while after the first ota, it will get the NRF_ERROR_STORAGE_FULL...
I have an encased nRF52840 dongle that is visible to nRF Connect. However, when I try and select the displayed device I get the following:
I cannot press the reset button...
Hi,
1. What modem versions does this board support?
For example mfw_nrf9160_1.3.0？
2. This board programmer this example:lwm2m_client
Using AT + CFUN? No return...
Dear Nordic team,
in our multiprotocol (BLE, ZB) application ( nRF5 SDK v4.1.0 )we are facing following severe issue relating to the ZBOSS stack: When a router leaves its...
Hello sir/Ma'am
I am working on a project in which i am using some BLE peripheral devices, an Central device and an Android app. I want to get data on android app from central...
I'm trying to program nrf9160 but getting an error due to readback protection.
I have tried the following commands:
nrfjprog --recover
nrfjprog --recover -f NRF91
...
I set an NOPULL type input GPIO, and I found that if I put in a voltage of about 1V,
the nrf52832 will produce a current of about 30uA,
I want to know why it can be happen...
HI
I have using nrf5340 DK for the past 7 months. Sometimes, The DK gets powered up only after 2-3 minutes after giving the power supply from the PC. Even after powerup...
I'm working on a project based on nRF52840 and nRF5 SDK16. I'm using BLE with softdevice S140 7.0.1 and USB CDC ACM for communication with a USB host. Ultimately the problem...
Hi,
I'm trying to run ble_app_blinky_pca10040_s132 on Fanstel BT832 custom board with no success. After writing/verifying the app using the SES it jumps to 'unknow function...
