Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hello,when i get connected to the phone,when i call err_code = ble_hts_measurement_send(&m_hts, &simulated_meas) and err_code = ble_bas_battery_level_update(&m_bas, battery_level...
Hi community
In order to set a reasonable CONFIG_MAIN_STACK_SIZE I'd like to have a stack usage report.
I've seen the option CONFIG_STACK_USAGE . This generates an additional...
We read 3.6 V using the ADC, for our mass production devices. The error rate is about 50% of the devices show wrong values between 3,05 and 3,4 Volts.
Even though the ADC...
Considering nRF52810 for a new project with a dead-simple application. Background:
- application is just data-pipe from mobile app to UART, both ways. No encryption/decryption...
Hi Team,
we are using the I-Jet Debugger with IAR IDE , How to load the Bootloader with this setup. Is there any additional settings required for this like Segger J-Link...
I have created code in GPIO read/write code with zephyr os. I did not add GPIO in .dts file. How the my GPIO example is working.
GPIO driver is not needed .dts support ...
Hello, All,
I am using the nrf connect tool on VS code for development, but i have a questions:
The west and some other python plug-ins used by this tool are installed...
Hello everyone. I am trying to develop a communication link between two nrf52 devices. I want to collect measurements from some sensors, pack them into a single data pack...
Hello,
I'm running Buttonless DFU successfully, but I would like to know if it is possible to start the application with the DFU service disabled, and activate it only later...
Hi, I have a firmware that runs well on nRF52833 dev kit (SDK 17.02) and I am trying to port it to a Laird BL653 dev kit. The firmware has a bootloader and it can perform...
so I use the default sdk in
D:\sdk\nRF5_SDK_17.0.2_d674dde\examples\ble_central\ble_app_uart_c\pca10056\s140
when i press button on nrf52840dk(pca10056)
it should at...
Hi,
I am evaluating the nRF5340 SoC and the recommended toolchain nRF Connect SDK (NCS).
I see that NCS is based on Zephyr RTOS, which provides also some drivers (spi...
Hi! I'm trying to save some variables after a watchdog reset for debug why my application hangs up.
I add a ram section on flash_placement.xml ( <ProgramSection alignment...
I am looking for Static analysis tool ( which is in compliance with standards MISRA-C and CERT-C) to be integrated with Segger Embedded studio.
Is there any preferred...
Hi
I am looking for a ways to perform DFU over serial, surprisingly i dont find any ways except this thread with no answers
https://devzone.nordicsemi.com/f/nordic-q-a...
