Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
Hi Nordic,
I was checking the ble_app_uart_coexist example application and it says it is a combination of both UART & Mesh. So would this support provisioning via mobile...
Hi, team. ********** environment : SDK : Mesh v3.2 (w/ SDK v15.3.0) SoC : nRF52840 IDE : SES ********** I am challenging to handle each event, such as Mesh receive interrupt...
Hi all,
Radio notification inactive state interrupt is coming but I was not able to do any action by comparing it.
I am thinking, if radio_evt is false then it is radio...
Hi,
I need trigger repeated SPIM via PPI for a batch of samples until the given RAM buffer is full. Then I need start another round of batch SPIM with another buffer.
...
Hi,
I am trying nrf52832 with pca10040 board. My app uses s112 soft device and also SPIM0 to collect data from a slave device. No event handler has been used when initializing...
I want to know how to control BLE connection of nRF52832. I am using softdevice S132. I have a device that works centrally and a device that runs peripherals. When the peripheral...
nrf52832.
SDK14.2
Segger ES V3.34a
Options for Sequential Serial numbers
We have managed to program a single serial number into the UICR, using our Development...
I am trying to interface I2C EEPROM (AT24C512) with nrf52840 and I am directly writing to and reading from the registers mentioned in the datasheet. I am seeing the i2c waveforms...
Hello -
We are also bumping into the problem described here , where it is not possible to initialize LESC when BLE is initialized from a FreeRTOS task. The nrf_stack_info_overflowed...
nRF52DK
external board with 51822 and mems
I connect my external board with nRF52DK as this (left is board, right is nRF52DK):
SWCLK -> SWDCLK
SWDIO -> SWDIO
VCC...
Hi,
I got some troubles on the communication distance between the two units which one acts as central and one acts as peripheral, I tried to adjust the BLE parameters the...
Dear Sir,
I have enabled my project for SPIM+EasyDMA.
I am configuring the SPIM transfer nrf_drv_spi_xfer with additional flags like,
NRF_DRV_SPI_FLAG_NO_XFER_EVT_HANDLER...
nRF51822 QFAA
At first I set up the RAM size to 0x1F80, it works fine. However, after I try to use RTT to print log, I got the compile error: region RAM overflowed with...
