Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi,
I want to use I2S to drive the speaker,just like playing the prestored samples from sounds.h in thingy:52.
However,i can't drive the DAC by I2S.Is there anyone have...
I just got my nRF9160 DK. Unfortunately the out of the box demo didn't work:
LTE LC config ... [00:00:01.029,876] [1;31m<err> net_if.net_if_init: There is no network interface...
Imagine following use case:
Alice has a peripheral bonded with Alice's phone (central)
On the peripheral, Alice switches to a "guest mode" which disconnects from Alice...
HI
UUID scan filters are set and enabled.
I was capturing peripheral device MAC id via ble_evt_handler.
i was expecting filtered devices should be visible but when i...
HI
I am trying filter peripheral devices based on UUID while scanning. I have set, enabled the scan filters but still output is displaying all the peripheral devices irrespective...
Hi I am using nrf52832 board and SDK15.2 I have below requirement:
Nordic board should act as central as soon as it gets booted and scan for particular service if present...
Hi, I have modified the twi_scanner example of the 52840 DK to be compatible with nRFDongle.
I fully erased the dongle with Segger and passed the new hex file with SWD cable...
I found this very useful Throughput Measurement Application for for Threads: http://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.thread_zigbee.v2.0.0...
HI, I have a custom service with customs characteristics and I need the maximum speed posible.
I have one service for write without response and another service only with...
Hi,
We implement oob pairing using NFC.
According to my knowledge NFC is used as "private" advertising channel (this is what OOB means) i.e. peripheral address, encryption...
Hi,
I have created a custom Serivice and custom characteristics in the attached application
Please find the attached application which create a custom Characteristic with...
hi nordic,
i had a nrf52 dk where it should only advertise to specific device like my phone with nrf connect app and that nrf52 dk should not advertise to other devices...
Hi,
My name is Bruno and I'm developing an Application which consists on:
Connect to a BLE device (I'm using Nina B112 from u-blox, which contains a NRF52832 SoC) through...
So I have successfully built & deployed the Light Switch Demo - and it works.
But where do we go next?
The documentation seems far too close-in focussed on the microscopic...
Hi,
what is the typical or max wake up time of the nRF52 from the RTC or GPIOTE irq (when configured as sense for low level input)?
In my setup, I see a wakeup time...
