I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hello,when i get connected to the phone,when i call err_code = ble_hts_measurement_send(&m_hts, &simulated_meas) and err_code = ble_bas_battery_level_update(&m_bas, battery_level...
I got the Dynastream N5 kit and have successfully used it with limited ANT work and was trying to get BLE working but can't get a driver for the USB dongle. On the 51422 product...
Hi All,
I am working in the sleep mode with system off and wake up with internal RC clock.
It function well when connected to EV board...
I see the "Emulated System...
I have a custom board with an I2C connected sensor ADXL345. I have to do GPI/O initialization to select the I2C. This works because I can read the ADXL with custom I2C commands...
Hi
I am using nrf52840 in my custom board. I have a gpio button which is assigned for as a factory reset button. So when i press the button the whole board needs toi be...
Hello,
we are looking to develop multiple BLE audio source which sends the mic data to the receiver and the receiver receive the audio data from multiple transmitters...
In my design, I aimed to isolate the USB interface. To achieve this, I used the Analog Devices USB isolation chip, ADUM3160BRWZ, to isolate the connection between the PC and...
When I need to switch between 1M and 2M
I create an object of the type bt_conn_le_phy_param and fill in the parameters appropriate to the radio mode I want, and then I call...
Hello,
I would like to know if the nRF9151 is suitable for building a product that will be able to monitor (read) multiple pulse signals originating in utility meters (electric...
We are using nRf5340 and nRf7002. In our application , we are connecting wifi and goes to ksleep for few minutes.
After wake up from the sleep. wifi is not reconnecting...
Hello all,
I ported an old nrf5 application from SDK 12.3 to SDK 17.1. It uses S112 7.3.0 and FreeRTOS. Unfortunately I am getting time variant softdevice hard faults at...
While testing nRF FOTA download library we noticed that it supports only one image update at a time (download image, then reboot).
Irrespective of the image (either application...
Hello, I just upgraded from SDK v2.5.0 to v2.7.0 and now I have a problem updating the bootloader.
In my project I have b0, the mcuboot (in s0 and s1) and the application...
Hello, I followed Getting started guide for the nRF54L15 PDK ( Getting started with the nRF54L15 PDK (nordicsemi.com) ) and bumped into a problem when i try to build "hello...
I am using the following example as a reference for setting the TX power in a peripheral Bluetooth connection: https://github.com/nrfconnect/sdk-zephyr/tree/v3.6.99-ncs2/samples...
Hi, we are doing testing with a Nordic dev kit and looking for ways to check the status of GNSS.
We are becoming familiar with the XGPS command and notifications: docs.nordicsemi...
How can I return from k_sleep (or any other "sleep" method) when an interrupt occurs?
I would like my device to sleep (low power) until a GPIO pin toggles, then wakeup to...
