Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hello everyone I am gradually learning Bluetooth, it takes time, but I need a temporary solution, I need a so-called adapter, Bluetooth <-> UART, to simply transfer bytes...
Hi all,
I develop my own IoT board using NRF52840-QFAA (Rev3), I am follow the Intermediated Course about Creating custom board but some how my board cannot run blinky example...
With a npm1300 I'm able to charge (for instance, the LED showing charging status is on, BCHGCHARGESTATUS is reporting the different steps..... ) but the battery current reporting...
Hello
When following the guidline of a new way to extend boards , VSCode "Add Build Configuration" is blank. Am I doing something wrong or this is not yet supported by...
Hello,
Our company makes module using nRF52840. And we also make development kit with it.
I recently programmed open bootloader built-in hex in nRF5 SDK v17.1.0 (examples...
nrfConnectSDK V2.8
Toolchain
Board: nrf5340dk
Hi, while compiling ncs-spi-master-slave-example , I am getting below errors
In function 'spi_init': C:/Users/hello...
I am currently working on a Direction Finding project, but I am facing an issue in prj.conf .
I use an nRF52811 custom board for Direction Finding. In the board selection...
Hi,
EDITED: This appears to NOT be related to any open circuit, the SAME behavior comes even with abrupt changes to the current scale, without any interruptions. Additional...
Hi, I'm trying to install modem fw using the script given by Sigurd : https://devzone.nordicsemi.com/f/nordic-q-a/53208/updating-nrf9160-modem-firmware-through-the-command...
Hi.
code base is sdk 17.1.0
MCU : nrf52810
Softdevice : S112 (7.2.0)
use SES 5.42a
step1. modify NRF_SDH_BLE_GATT_MAX_MTU_SIZE form 23 to 50 in sdk_config.h
...
Dear nRF experts. We are a module manufacturer and we have designed an nRF45L15 module. We are doing a series of verifications. When we were doing the connection test, we...
Hi,
the nrf54L15 datasheet states on SPIM "CSN and DCX are not present in all configuration" (p.559). But I can't find the information, when CSN is available.
Hi,
I use Nordic connect SDK and have to create a new revision for a custom board, because there are some hardware changes. I managed to create an overlay for the new revision...
MCUBOOT contains a flag MCUBOOT_OVERWRITE_ONLY_KEEP_BACKUP that stops it erasing a big chunk of the start of the secondary image after an update.
We would like to set this...
I'm looking for an nrfutil command to replace this command:
nrfjprog --memwr 0x10001080 --val 0x12345678
My goal is to write a serial number to the UICR CUSTOMER[0] register...
