Hi,
There is much talking about the "large data transfer" over BLE, the l2cap channel being the best option for the moment.
However, does anyone know the datarate achievable...
NRF24AP2 with MSp430F149 . ASYNC 9600 N 8 1
step 1 : reset NRF24AP2 with reset pin , and received a pulsing signal through RTS pin
step 2: send a char (0x4A) to NRF24AP2...
Hi guys,
I am using the gcc setup to program my boards. However for flashing the softdevice I use nrfgoStudio. SO I downloaded the hex file and fashed the siftdevice. But...
How do you create hid information for a joystick and send it over BLE. Nordic doesn't seem to have
primitives for this (they have keyboard and mouse facilities). I'm working...
I use a PCA10001 board as peripheral role of heart rate service and it can be discovered by control panel. But as I download the experimental program of central role of hrs...
I'm reading the source for the nRF Toolbox app for Android 4.3 and comparing it to the Proximity Profile spec from the Bluetooth SIG, which has this to say about path loss...
Hi I am using the Zephyr code base after trying to update the ncs to 2.1.2 from 1.9.2 I notice that the function "flash_area_open" is returning a -2 error as it couldn't find...
Hi,
I am using nrf mesh sdk v5.0.0 and am using sensor server model example to build our own application on top of it. SOC we are using is nRF52832. I have enabled the...
Hi,
I have few doubts regarding the internal flash of nRF52810. I am not using SoftDevice. I am using SDK 17.1.0
I would like to write around 20 bytes to internal flash...
board : nrf5340 sdk : nrf-connect v2.1.2
Hi. I am studying OpenAmp and RPMSG using NRF5340DK board.
I looked at the examples below for studing OpenAmp and RPMSG.
C...
nRF Connect SDK 2.2.0 on Windows 10 pro, I have a nrf52840-DK and a nrf9160-DK. I would like to test a simple OpenThread CLI application
I have the following prj.conf
...
Hi, team.
I am trying to find a way to write some persistent data in factory.
The data is a couple of certificates and should be written differently for each devices....
I am a beginner, and there is no problem with scanning and receiving data in RTT Viewer. I am currently stuck on how to use CDC ACM US. i have notice there are example on...
I am interfacing with a part that uses the same pin, P0.6, for two purposes:
1) The pin is used for UART communication. MCU RX input.
2) The pin is used as a GPIO. MCU...
Hi Everyone,
I have a custom board with a nRF9160. I have updated the firmware to 1.3.3. I am using SDK 1.9.1. I found that the board works well with the GNSS sample from...
Hi, I have an application where I need a latency below 100µs between transmission and reception over the air of a 32 bits payload.
We are currently evaluating the ESB protocol...
May I know if developing using the example of proprietary_rf that does not use BLE in SDK is also subject to a user fee? (If there is a usage fee, I would like to know the...
Hello,
I have an issue with BLE-Mesh, wherein If I provision a device and then flash the board with a new image (I do not erase and flash), the device name & provisioning...
Hi all,
we are using UART uart_rx_enable() to define a timeout of 500. Most of the time, event UART_RX_RDY is raised as it should be after a timeout. If, for example, we...
Hi!
Which is the right way to install nrfconnect SDK for VS Code for linux? Is it automatically or manually as described in the documentation?
Regards.
Hello all, I hope you are doing well.
I Have a project on NRF52840 in which I have multiple sensors connected to the NRF52 and the sensor data are storing in the SD card...
