Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hello,
I am writing about an issue that come up with enabling MCUboot.
The device is a temperature/humidity data logger recording data into Storage Partition with NVS...
Hi Madam/ Sir,
I am using your PPK II to measure current consumption. Based on your document, this device use an internal resistor to measuring current. And the PPK features...
Hi, here I have a custom made board that has a MDBT42Q module (nRF52832 based) and has connected a RFM95W LoRA module, using this simple send lora code:
# include < zephyr...
Building the app with the factory data provider (CONFIG_CHIP_FACTORY_DATA), active logging for Matter (CONFIG_MATTER_LOG_LEVEL_DBG) and immediate logging (CONFIG_LOG_MODE_IMMEDIATE...
Hi,
I'm migrating a vscode project from 1.9.1 to 2.1.2.
I'm testing on nrf52840dk_nrf52840.
I'm using I2S.
In the 1.9.1 environment I have an overlay.
&i2s0: &i2s0...
Goodmorning,
I'm using nRF5_SDK_for_Thread_and_Zigbee_v4.2.0_af27f76
in file /external/zboss/src/zcl/zcl_thermostat_commands.c
at line 246 there is this code:
...
Hello ,
I am developing asset tracking solution using BLE Beacon (using nRF52832. Not using AoA and AoD feature) and BLE Gateways (using nRF52833). I just want to detect...
Hi, I'm trying to flash the nrf9160 through Visual Studio Code and I'm getting an error. I'll describe the error and what I tried to fix it below.
1 - First I tried to flash...
Hello Nordic Team,
I am currently using GNSS Sample to get the location data for the nRF9160. However, I am not getting the data as I keep getting this output.
May I...
Hello,
We have an application built with MCUBoot running on a nRF5340. We have used NCS v1.7.0 and NCS v1.9.1 versions for our devices.
All MCUBoot, app core image and...
Hi Nordic Team,
We want to verify controller functions on our own chip with core5.2, so I want to connect it with nRF5340 board by HCI uart, so that I can verify CIS or...
Hi,
followed below link to do the firmware updating using DFU service with "nRF Connec"t application on Android mobile.
https://novelbits.io/nrf52-ota-dfu-ble-part-4/...
I observed that the GPS antenna of my Thingy:91, version 1.6.0 - that has the TRIO mXTEND chip antenna component NN03-310 - is much less efficient that the GPS antenna of...
Hi we designed a custom board that contains the wifi module: EWB-STERLING,( 453-00014R ) In my board, I routing the USART1 pins to FTDI chip (FT4232 with 4 Channels). I search...
I have a NRF52840 Dev Kit and a ESP32-S3 Dev kit, I want to do a SPI communication between them. Here NRF works as SPI Master and ESP works as SPI Slave. I am using SDK-17...
