Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am using openOCD for flashing hex files to an nrf51 target. I have got the flashing process working.
However, I seem to be running out of space, the nrf51 has 256kB flash...
I'm trying to integrate MCUboot into my application, as immutable bootloader (CONFIG_BOOTLOADER_MCUBOOT=y). Building succeeded, but after programming the board gets stuck...
Hi,
I am using nrf52840, NCS v2.1.2.
I add MCUboot in my project, but got ‘Failed reading sectors; BOOT_MAX_IMG_SECTORS=256 - too small?’.
I add some log in MCUboot...
Hi,
I have been using the nRF5 SDK for years and the reason why I chose Nordic was for the low power consumption. Then when I was designing a new product using the nRF52840...
Board: nRF5340dk
SDK version: v2.1.0
My goal is to transmit 240 bytes of data every 5 ms using GATT notifications and 1 Mb PHY.
In the attached sample, I have my dev...
I added two extra buttons to ble_app_blinky (SDK 17.1.0) - port 1.10 and 0.31 I am running the code on an nRF52840 Dongle. The additional buttons are configured exactly like...
Hi,
I am using the sensor server example available in nrf5 sdk for mesh to build my own application on top of it. And the SOC we are using is nRF52832. I am trying to erase...
I see in the nrfx_uarte.c file the statement NRFX_LOG_INFO("Transfer about to send : %d bytes", length);
How can I set the logging for this file on?
#define NRFX_LOG_MODULE...
Hi,
My apologies if this is the wrong place for this.
I've been using the Power Profiler with the PPK2 and I'm very happy with the product, just have a couple small suggestions...
Hi there! I am facing " <err> download_client: Unexpected HTTP response: 400 bad request" error whenever I am trying to download full modem update from AWS S3 bucket. My environment...
Hi,
I attend the introduction course for the nRF's, and I am at Lession 3. The task is to print 'Hello World' to the device, using Serial Port and COMx. I have made the...
Hello,
As per the requirement of my project I need to add a header file into one of the thingy:53 sample.
Can you please guide how can I add a new header file into it...
Hi ,
I am working on thingy53 and using ncs 1.9.1 I need to enable the BMI270 sensor and need the acceleration and gyroscope data from it. So for that, I primary using the...
Hello,
I am using the provisioner example to provision and configure all my sensor nodes in my project. My use case consists of around 60 sensor nodes. While provisioning...
