Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Hi,
I'm trying to measure the communication distance with Coded PHY using two nRF52840s and the demo software below,
but there are some problems. They are shown below...
It has been about 4 years since I was developing for the nrf52840. During that time, it seems Nordic has moved to promoting the VS Code IDE vs. Segger Embedded Studio. If...
Hello,
I'm using the file app_update.bin of my project to execute a FOTA. I know that the first bytes indicates if the file is an application firmware, modem full or modem...
I was wondering if there was any documentation (graph or otherwise) that shows the efficiency of the DC/DC converter vs. supply current.
The product spec describes the...
https://devzone.nordicsemi.com/f/nordic-q-a/70679/call-to-nrf_sdh_enable_request-fails-in-sdk-v16-0-0-works-in-sdk-v15-3-0/291135?focus=true
I've been suffering from the...
Hello,
I want to implement the interrupt functionality and based on my understanding I can implement it using GPIO or ISR function.
In case of GPIO (APIs here ):
For...
Hello,
Is there a list of Android devices that will run nRF Connect, or will it run on any Android device?
Which Android app stores is it available in please?
Kind regards...
Hi,
We are using a module which includes nRF52832 in a custom board. After a while devices stop working but when we re-connect battery device starts working again exept...
Good morning,
I get a i2c nrfx twi error on startup and reset whenever the i2c sensor is switched off (<err> i2c_nrfx_twi: Error 195952641 occurred for message 0). I am...
Dear all,
I would like to ask if the nRF5340 LE audio can connect to a mobile device while another LE device is also connected to the mobile.
For example, is it possible...
Is it possibe to configure uart with baud rate of 512 on nrf52832?
I tried to configure the uart with this baud rate, but I am not able to get the uart communication ...
Hello everyone i need to update the Advertising Data of the device but i am not sure the correct way to do it. First i have the next struct of the Adv Data that i want to...
Thank you for your help. We are currently developing hardware using nrf52840. I would like to use pin numbers to control LED lighting, but when the port number is 0, I can...
I am developing a custom application that was started from 1 of the bluetooth examples for a customer and though I have been using the same custom PCB for 7 months, I am now...
