Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
When I add example timer to example ble_app_uart an error occurs.
I followed the template and pasted the code.
Here is my sdk_config.h
An error occurs when...
Hi,
I am programming the nRF52833 DK using the nRF Connect SDK (v2.00). I have built and flashed the Bluetooth: Peripheral HT sample from Zephyr to both boards successfully...
Hi all
I'm using the nRF52832 and I've configured P0.21 as RESET pin.
When I reset the nRF52 via P0.21 while the debugger is running, the nRF52 actually resets but it...
I am trying to implement the ble_app_hrs example from nRF5_SDK_17.1.0 and my board is nRF52840 Dongle.
After program the board, the board can advertise and I can find the...
I want to use nRF5340's GPIOTE and DPPI implementation, pull up PA_SWITCH_CTX_PIN when NRF_RADIO->EVENTS_RXREADY is triggered, and pull down PA_SWITCH_CTX_PIN when NRF_RADIO...
Hi guys,
I have an interesting idea - organize a network for realtime audio communication. Basically duplex Walkie-Talkie but using bluetooth headsets. I tried to use ESP32...
Hello everyone,
at the moment I am working on a BLE program which collects data from various sensors and passes it to a Central device. For the transmission the BLE NUS...
I am using ESB with dynamic payload lengths. When I use length 252, I am sending the alphabet repeating, and I can see that the data cuts off around position 30 and repeats...
Are there any known issues when using a nRF52840 and S140 6.0.0 soft device and trying to transmit at +8 dB? From our measurements is appears that +4dB does indeed increase...
Hello,
I am using the nRF 9160 DK board. I am trying to create simple thread in Zephyr.
but the thread it's not running.
this is the code:
I tried also the other...
I accidentally pressed "verified" on https://devzone.nordicsemi.com/f/nordic-q-a/91104/making-rand-work-on-nrf52-nrf53-with-nrf-connect-sdk when it wasn't and I don't seem...
I am testing my own mesh protocol based on 802.15.4 using the NRF52840 dongle.
The reported RSSI value from nrf_radio_rssi_sample_get() never goes below -89dbm.
On the...
Hi,
I'm using a nrf52832 and NCS 1.9.0 and I would like to be able to use SMP to make firmware updates using BLE. I'm was able to perform FOTA, but the flash is divided...
Greetings!
We are trying to troubleshoot occasional hangup issue. We run the app in debug mode. When it hangs up, we hit pause and got the followings in the Call Stack window...
Hi,
I want to use nrf5340 dk board to debug nrf52840dongle, i have connected two board with a cable and have checked the signal is good( nrf5340 debug out p19 ------ nrf52840...
