Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Specifically, the example is examples/ble_central/ble_app_uart_c
I want to first verify my understanding of this example. In this example, should I be able to type in my...
Hello,
I am currently trying to flash a nRF51422 chip that will be placed on a custom PCB board using the pin20 on the nRF51 DK board. I had connected the chips pins as...
Hi,
I'm using TIMER1 CC0 for SAADC sample triggering through PPI and it's working well.
In order to check sampling frequency, for debug pourpose, I'm using PPI fork for...
I've been using the radio functionality directly, without the nrf sdk. Everything works great for 802.15.4 transmission and reception with one really odd exception: packets...
Can someone please post a simple example of using the internal oscillator with BLE? Modifying the ble_app_blinky example to use the RC would be ideal. No matter what I do...
Hi support team,
Now i am trying to understand the LPN machenism based on the LPN example. I cannot make sure where the bear handler is started.
There is a function bearer_handler_start...
Hello,
I'm planning to work on a device which should have two nRF5340 modules on a small PCB (they will be max 2cm apart from each other). Both modules will broadcast data...
Greetings,
I am using the NRF53 DK along with the Zephyr/Beacon (nRF Connect SDK v1.91) example for an ultra-low power application. I would like to know how I can change...
Hi,
I have nRF5340 DK and nRF52840 DK and Flashed Central_hr_coded in nRF52840, Peripheral_hr_coded in nRF5340 DK. Followed the steps of Testing as showed in below link...
I am following various tutorials on how to run an example DFU
I've tried: https://infocenter.nordicsemi.com/index.jsp?topic=%2Fsdk_nrf5_v17.1.0%2Flib_bootloader_modules...
Hello,
I setup a BLE Peripheral that advertises a service with 2 notifications. Each notification has 240 bytes of payload data. When I connect with a client and subscribe...
Hello,
I followed the following guide for creating a modified Blinky example app that boots from the mcuboot. I attempted to flash both the merged.hex and zephyr.elf to...
I am using NRF52832 DK, SDK 17.1.0, S132 Softdevice, Segger 5.42a and rtt viewer v7.62.
I am using blinky code from example.After building and debug the code I disconnect...
I want to send the data packet from the BLE using GATT service and after that BLE mesh is initialize, using the Mesh opcode need to Disable the GATT service of the BLE. For...
