Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
Hello Support Team,
I am currently testing the new Channel Sounding feature on two nRF54L15 boards, on which I flashed your Channel Sounding samples ( initiator and reflector...
Content: I’m working on integrating the nRF7002 EK over SPI with an nRF54L15 using nRF Connect SDK v3.1.1 . While setting up the workspace, I noticed that the Wi-Fi driver...
I am working on a project where I am using the npm1300 with host nrf5340. The BUCK1 powers a sensor and BUCK2 powers the nrf5340. I have a SPDT switch connected to GPIO0 and...
I used the nRF Audio Example to build a BLE audio device. I use the test tone generator functionality. I was previously using nRF Connect SDK 2.6.1 and the test tone generation...
I am an FAE with Ezurio, we have a customer who was running through the nRF Connect SDK Intermediate training on DevAcademy and they ran into issues with AuTerm in Lesson...
## Description
On the nRF54L15DK, the measured floor current increases significantly when the GPIO is configured for button edge detection.
### Observed Behavior
* Floor...
Hi,
I am quite new to nrf's and zephyr and I'm working on a product that requires Direct Test Mode functionality. I started with the DTM sample and am now looking at how...
Why do I often fail to compile the examples due to west? The prompt suggests that I need to upgrade west, but I am unable to do so?When directly upgrading West through VSCode...
The solution for "nRF Connect SDK Intermediate - Lesson 9 Exercise 5" does not appear to boot-up after flashing and gives the following output on the com port:
*** Booting...
Currently with the DECT NR+ modem API on nRF91x1 I can schedule rx operations in mode NRF_MODEM_DECT_PHY_RX_MODE_CONTINUOUS given to nrf_modem_dect_phy_rx via nrf_modem_dect_phy_rx_params...
Is there a way to create custom battery profiles of non rechargeable batteries for the nPM 2100 PMIC? Is the nPM Fuel Gauge board compatible with the nPM 2100 EK?
Hello,
I am using nRF5340 with nrf v2.7.99-cs2.
We have interfaced External flash MX25R over nRF5340's QSPI channel. We are using XiP as well and some part of code lies...
I'm developing a Bluetooth mesh lighting controller on a custom board using nRF Connect SDK v2.6.1. I'm trying to add a Sensor Server model to report energy usage, but I'm...
Environment : nRF52833, NCS v3.1.1
Hi. I evaluate PAwR project in my Solution.
PAwR is Fine. But get/set Tx Power is issue.
before add PAwR, My solution used common...
Hello,
I am developing a custom IoT device based on the nRF9151 SiP with a Qorvo QM13345 SP4T antenna switch controlled via RFFE 2.1 interface. All RFFE AT commands fail...
