nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
Dear all,
I used till now an application to route BLE data over serial port through the dongle USB nrf52840, SEGGER IDE and 1.9.2 nrf conneck. All works well.
Now I'm...
I have an application that requires invoking multiple commands to the same node in quick succession (multiple times a second).
To evaluate the feasibility of this, I flashed...
I am doing DFU using nRF52832 board. Is it possible to update partial firmware?
For example, Is it possible to change only blinking LED without changing other stuff from...
Hello everyone! I am having some trouble in connecting two peripherals to a single central station.
As peripherals I'm using 2 nRF5340DK flashed with the UART-Peripheral...
HI all,
So after realizing that I needed to Just-In-Time provision my Thingy 91 in order to add the device to my nRF Cloud account, I began the process described in this...
I have a project that was building, but now on restarting VS Code, I cannot access the build configurations.
The list shows a configuration as present, but when I expand...
Following instruction here for setting up NRF52840-Dongle as a radio coprocessor for use with OpenThread Border Router.
The error is at the second step when executing "...
Hi,
I have a working application where at some point, I erase some part of the flash with following code :
On nRF52 aPageAddr is:
(not sure why other variables are...
Hi all ,
I 'm experiencing issues with MQTT client connection on an nRF9160 board via LTE -M .
Some context : I 'm trying to connect to a MQTT broker via LTE -M (actually...
Hello,
I have an NRF9160DK board and a custom board running the SLM application that are exhibiting similar behaviour. Both boards work fine with the supplied iBasis SIM...
Hi,
I'm using ble_app_att_mtu_throughput to communicate some data from a nRF52832 to another one. I reached my goal (1.4Mbps) but now I would know what the two board communicate...
Hello,
I have a question regarding the consumption of the nRF9161 DK board when it is under the following conditions: MCU on IDLE, modem off, wake on GPIOTE input (event...
Hi,
I'm struggling to use ble_app_att_mtu_throughput and spi. Some help?
When I merge the two codes the main code (ble_app_att_mtu_throughput) doesn't work.
Thanks...
Dear expert.
one of my clients manufactures medical devices.
as you may know, medical devices need to special certification depending on the country, such as North America...
Hi,
For the SoftDevice controller, how can I send LL_MIN_USED_CHANNELS_IND messages? Is there an API for this, or what scenarios trigger the sending of this message? Thanks...