Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Hello,
I am trying to commission a device running the CLI sample to an OTBR I configured following https://openthread.io/guides/border-router (the OpenThread official guide...
Hi
in Zephir nrf9160dk_nrf9160_common.dts the SPI pins are defined
&spi3 { compatible = "nordic,nrf-spim"; status = "okay"; sck-pin = <19>; mosi-pin = <18>; miso-pin ...
hello,
i am using nrf52832 with sensor which uses uart communication and using sdk 15.2 but i could not get my excepted values in rx buffer which is of 3 bytes and values...
hi,
i am working with nrf52832. system on sleep mode is working ok in ble_app_uart example by commenting " //err_code = sd_power_system_off(); //APP_ERROR_CHECK(err_code...
I'm guessing this isn't the best place to ask this question. Please redirect if you can suggest a better place to ask. Thanks! I'll recopy the question here:
NRF has an...
Using
SW : NRF_SDK_16, SDK_MESH_v4.0
HW: NRF52840 DONGLE.
I have implemented light_switch_client which also has USB part initialization and then added in USB_DONGLE...
I am working on the nRF5340DK and NCS v1.5.0
Acording to this example https://github.com/NordicMatt/multi-NUS , I used the Throughput sample as the fundermental project...
I'm measuring the power consumption of the BLE Beacon example and got the graph below for one beacon transmission. I'm wondering what those smaller peaks are with 1ms period...
Howdy,
I'm evaluating the nRF Sniffer + nRF52840 dongle as a stop gap BLE sniffer solution, but I'm having a lot of issues setting it up.
Re: Installing nRF Sniffer (...
Good morning,
I am working with the AOA module of the nRF Connect SDK. I have been able to configure and program the transmitter with the CTE as well as the receiver and...
Dear Nordic,
we are developing an application based on SDK 17.0.2, it user FreeRTOS and BLE with Peer Manager.
We need to store few data in FLASH without confict with...
Hi
We are trying to get the DTM mode working for the NRF52 2nd BLE for testing BLE TX power and RSSI at the factory.
(1)HW setup is shown
(2 ) Procedure
We have...
Hello,
what are necessary that a Device automatically (without a 3rd party app) connect to the GATT Server with a HID Service.
I have implement a
HID Service,
Device...
