I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
Hi
We are trying to get the DTM mode working for the NRF52 2nd BLE for testing BLE TX power and RSSI at the factory.
(1)HW setup is shown
(2 ) Procedure
We have...
Hello,
what are necessary that a Device automatically (without a 3rd party app) connect to the GATT Server with a HID Service.
I have implement a
HID Service,
Device...
hi，
I'm use nRF52840 to developing a Computer Keyboard，i wish 8X18 matrix a total of 144 buttons，About keyboard button matrix, please help to determine which GPIO can do...
Hello,
I am trying to resolve some compliance issues with the third-party libraries that are used in the SDK. For nanopb, it seems like the changes in pb_decode.h mentioned...
Hello,
I want to configure pin 0.13 as a rising edge interrupt.
Is there any sample code to configure the pin and interrupt handler?
Thanks in advance.
Hello,
In a previous post I asked about scanning and connecting based on specific advertised data. After some testing I realized that my two nrf dks only connect sometimes...
Hello; We want to use the GPS peripheral of nRF9160. Qorvo QM14501SR LNA is used in your evaluation board. QM14501SR is expensive for our project. Can we use LNA without band...
Hi,
i am working on nrf52832 . i am facing advertising issue with custom board. controller advertise only when i touch 32.786kHz crystals or two capacitors with my finger...
Hi,
I use example projects Thread: CoAP Client and Thread: CoAP Server . I can send and receive data over CoAP. My purpose is to use CoAP, CoAPS and UDP tohether. If client...
nrf_ringbuf has a bug which happens when mixing nrf_ringbuf_cpy_put() with nrf_ringbuf_alloc() and nrf_ringbuf_put(). After copying data with nrf_ringbuf_cpy_put() a later...
Hello,
at the moment we are trying to realize a low power delay with the usage of the APP_TIMER.
We need a low power delay over 10 seconds.
This is our attempt:
...
Hello,
we are developing an application with a nRF52832 on a custom board. The application works fine. The application on the nRF52832 consumes 2.2mA @ 2.5V.
The other...
Hello,
Our Project
at the moment we are developing an application with a BMD-350, which contains a nRF52832 chip.
The BMD-350 is on a custom PCB with another microcontroller...
