I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Set up: Rpi Bluez 5.72 (provisioner)
nRF DK (light example)
steps:
1) trigger scan un provisioned devices from Rpi
2) able to see nRF device in scan results
3) start...
Hello,
currently I'm migrating a project from connect SDK 2.6.0 to 2.9.0. After some changes according to the migration guides the project builds fine and also runs.
As...
I would like to use nRF52832 DK to test Nordic UART Service (NUS). But west build failed with the following messages. What is meaning of "zephyr_pre0.elf section `noinit'...
Hello,
I am attempting to use the nRF7002EK shield with my nRF54L15PDK development kit.
I have custom code, but it's based on the wifi scan example provided by Nordic...
Hello,
I would like to know if there is a way that I could see the source code of the nRF Mesh Sniffer app for Android, just like the nRF mesh source code is available in...
Hi, I am currently using the nRF52832 MCU and have implemented hard fault handling as follows: I use the macro APP_ERROR_CHECK(err_code), which, in case of an error, calls...
Hi
I am trying to perform a full modem update on my nrf9160 DK board.
I started at v1.3.4 and successfully used the partial update method to go to 1.3.5
I then used...
Hi everybody, I'm looking to build a PWM generator with 2 outputs from 1-100Hz. Unfurtunately the current PWM API examples with Zephyr works only for 4-100Hz.
I've tried...
Hi,
I have just bought a PPK2 and (mistakenly on my part) assumed it must read the Voltage of the output as well (necessary for power measurements). I see now that it doesn...
I am using ncs sdk, my projects are under ~/zephyr-workspace. This is from an example project - blinkypwm. The clangd compiler shows the following erro: In included file:...
I try to simultaneous update (app + networkcore) with usb and external flash on my custombord And serial recovery, not DFU from app.
this is mcuboot config. I have set the...
i want to commission matter compatible smart switch into thread network.
but i'm getting internal error .
but other device like matter samples light_bulb (nrf52840dk)...
Dear Nordic Support Team,
I am currently using the nRF52840 development board and working on developing a dimmer switch. During the development process, I encountered a...
I just downloaded the latest version of nRF Command Line Tools: nrf-command-line-tools-10.24.2-x64.exe
My desktop is running Windows 10. The installation is successful....
