Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi all,
I'm programming nRF52833 with SDK17.
I want to use only one channel (for example 37) to broadcast advertising during advertise interval and also one channel of...
My team was looking to transfer a 20-byte value (or 'message') between a mesh client and server, what is the best way to achieve this? I have practiced with the light_switch...
Hi,
I am currently developing an application for the NRF52840 using a custom pcb powered through the VDDH pin using a 4.2v lithium ion battery. Part of my application requires...
Hi,
I am trying to following the instructions at: https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.iotsdk.v0.9.0%2Fiot_sdk_user_guides_java_coaps...
I have configured the dev kit by cutting the SB9 bridge. I am powering the device from the J2 USB port on the DK. I have not bridged SB12 or SB11 as I am powering the device...
Hello all,
I am experiencing a ~5uA oscillation (between 5uA and 10uA) in sleep mode, DC/DC converter enabled, no RAM retention. The total current is of the entire system...
i am working with jlink segger edu, in a custom board, it dont have swd TX, RX pins connected, only jtag pins. I Need to see if my gps conected throw uart is working or not...
I configured the pca63519-sr3_nrf52832_shield to fit on my board (actually disabled all peripherals, only the bluetooth protocol part), but found that the modified code could...
Hello! I wrote about the details in topic 66156 , but they did not answer me, because this question is already different from the original one. The drv_rtc.c library has this...
HI,
I have been facing a few issues with the BLE custom service, I am looking to create a Pedo meter service which displays step count information received from the sensor...
Hi Guys,
We have designed a custom board which is using BMD350.
Our application requires using the BMD350 in beacon mode and then going to sleep in low power.
We have...
I can listen for radio inactive event according to this post https://devzone.nordicsemi.com/f/nordic-q-a/9137/change-advertising-every-time-event but I am scanning at the...
Hi everyone,
I want to assign the DEVICEID to System ID characteristic (which is under Device Information Service). DEVICEID is a 64bit and I found that I could assign this...
Hello,
I am developing a sensor like a beacon. I want to measure the distance from the node. I record the RSSI sample for a few seconds and average it to stabilize the value...
Hi,
Can anyone confirm the advert sent in the attached is not corrupted in anyway? as I seem unable to scan my device with anything other then nRFConnect.
The Bluetooth...