I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
Hello,
I am working to verify custom services on my device using nRF52 dev kit.
I am using HR collector example code as reference. I am able to read the custom service...
Hi,
I am trying to add the beacon Eddystone features to my DFU buttonless application.
After compiling the code, I wrote the softdevice, the bootloader and the application...
I am integrating a sensor on SPI 1 with cellular but device get stuck in CPU idle when first transaction of SPI is made?
I am using nrf9160dk_nrf9160ns as board configuration...
Starting with the dev kit, where I get correct behavior. First, I make sure the RESETREAS register is all zeros. I do this like so: NRF_POWER->RESETREAS = 0xFFFFFFFF; while...
Hello,
I am using nrf9160 and want to test the just simple SPI function. The code that I found from github( https://github.com/Rallare/fw-nrfconnect-nrf/tree/nrf9160_samples...
Is there a way to set duty cycle before app_pwm_enable(&PWM1) call ?
Or some other simple way to switch on and off a passive buzzer signal without every time at off/on cycle...
Hi:
We're working with a 3rd party testing agency for our product that is using SDK 11 with S132 Softdevice 2.0.0.
If I understand correctly, the SDK allows up to 6 transmit...
I am trying to implement a system / integration test of a BLE device.
I would like to use the nRF52840-Dongle in my PC and use the PC-BLE-Driver for Cpp as the Central....
As you could see from the below image, the SCL signal at 400kHz is NOT a good square wave.
1) Why & how to solve it, please?
2) Also, why SCL is between 0.4V to V_DD=3...
I am now pulling my hair out with these drivers ... I'm trying to do what I think is the right thing and use the new nrfx drivers, but it's really not easy.
So this started...
Hi, I am using Zephyr's BLE for transmission In the peripheral, I record the time when I send the notify to cental (start time) Then when I received the central write_without_response...
Hello,
I have a peripheral that is connected to nRF52832 using I2C, in which I want to send some file to its memory. However, for sending this file, I need to stream it...
I have an existing BLE project that works as a mesh but does not use nRF SDK for Mesh. Using sdk 17.0.2, s140 7.2.0 on nrf52840s and visualGDB.
It works well for most clients...
Hi, I want to evaluate my anttena design. I have tuned it. With the dongle I can scan the air for radio signals, I see then my Wifi and I see the BLE radio of my board. Now...
Hello Nordic Community,
In order to measure battery voltage, I am using ADC with the code implemented as below:
In this, there is a while loop used to wait for ADC to...
