I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi everyone!
I'm running my Nordic Thingy 91 with "thingy91_nbiot_legacy_pco_dfu" and it works great!
Now, i want to make some specifics editions in the main code in order...
Hi, We are developing an application that should receive commands via SMS. The device runs on a fairly large and rechargeable battery so the power consumption is not the most...
Hello DevZone,
PCA10040 SDK 15.0.0 SD132
I written my own SPIM driver which uses the list function to read in a few bytes. I've set up my list as the example in the...
Hi,
What is the difference between performing a reset by using the function sd_nvic_SystemReset(), and performing a reset by turning the power voltage off and then turn...
I used "nrf5_SDK_for_Mesh_v4.2.0_src.zip" and "nRF5_SDK_V16.0.0", When I used scan_start() command, I saw Light_Switch_Server device and Light_Switch_Client device on the...
We have fabbed a PCB for the nRF52840 that has a QSPI chip. The pins are different from the example in the SDK. I was trying to get the SDK example (examples/peripheral/qspi...
Just test SDK17.0.2 serial DFU demo project on Nordic PCA10100 board by USB serial.and use s140_nrf52_7.2.0_softdevice.hex
Got below exception. Any clue for it please? ...
Hi,
I have my application based on nRF52840 device.
When writting a wrong passkey, my device is reseted.
Which can be the reason? I have already implemented event PM_EVT_CONN_SEC_FAILED...
Hello
To calculate the definite yaw value of gyro, I would like to use the mpu9250 with magnetic sensors. I used Martinsbl's nrf5-mpu library when I used mpu6050, can I...
Hi there,
what is recommended strategy to read/write data on uart?
Taking from sample, read byte-by-byte, on 115k, sometimes data are truncated.
Is there a possibility...
Hello,
I developed a thread network using the latest SDK for Thread v4.1. I also have the latest OpenThread Border Router running.
I cannot ping Google IPv4 from my Thread...
Hi,
I'm using nrf52840DK as a central device (sdk16 ble-app-uart-multilink-master) and my peripheral device is bt840 chip(sdk15.2 ble_app_uart_pca10056_s140).
My peripheral...
hello
i have 2 questions about System on mode:
i testing different types of power comsuption modes, i've tested RTC wake-up for system on mode, but i want to try to wake...
Hi, I want to run unit tests on an actual device (nRF52dk) - is it possible? When I'm trying to run `west build -b nrf52840dk_nrf52840` on `ncs/nrf/tests/unity/example_test...
I ask for your understanding of my short English. I am a student studying in Korea.
i using sdk 15.2 and nrf52840 dongle
When using the example of usbd_ble_uart of peripheral...
