Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Hello,
We are tweaking the TLS connection between nrf91 and mosquitto.
What ciphers does the modem support? Is there a list available?
Best regards,
Vlad
I want to send a byte on Nrf connect app upon receiving an GPIO interrupt using BLE_APP_UART code. I have configured pin P0.10 for the GPIO interrupt. I am using SDK15.2.0...
Dear guys,
I am implementing a module that monitors the battery voltage for our tracker device using NRF9160.
I do not understand how to set up two parameters for the...
Hi:
The urgent problem we are facing now is:
debugging hci_usb on Linux, how to set MAC address and send/receive files ? hci_usb fw : \ncs\v1.3.0\zephyr\samples\bluetooth...
Hi, I have no found clear steps to create DFU zip packet for old one softdevice S132 SoftDevice v2.0.0.
I try to build with nrfutil pkg generate but seems its working only...
Hi,
We are currently trying the Long Range (Coded PHY) on our advertised message, but we can't see any improvement (range of about 50meters). The range can even be smaller...
Hello,
I'm using a NRF52832 with SoftDevice s132 v7.0. I also have freertos. I have an app which advertises and scans. The app is set up to trigger a break point on assertions...
I have some customers seeing an issue with advertising/connection after successful DFU. Everything was working before DFU. The changes in the new firmware have nothing to...
I am trying to port the examples/ble_central/ble_app_hrs_c project from the 52840/pca10056/s140 to a 52833/pca10100/s140 project.
Having trouble in the port from the nrf52840...
Hello, I'm using softdevice 6.0, SDK 15.0, secure bootloader buttonless S132. On the phone with Android I'm using: nRF Toolbox 2.9.0 with DFU Library version 1.10.3.
I start...
I have built a custom chip with nrf52840 on it.
I use Ses as development tool.
I took as startingpoint for software SDK15.3 with Softdevice 140
I took the ble_template...
I use SES for debugging,
the chip is nrf52840 with softdevice 140, sdk 15.3
I ported a project from 2017 and now I'm ready to compile all without any error,
but as...
I try to build and debugg a programm from 2017: SDK15.3 Sofdevice 140 5.0.0.2 alpha plattform was eclipse neon
I switched the plattform to SES because neon sucks too install...
Hello,
We have a custom device using nRF52832 with a MTU of 20 bytes, and for one of the tests we are trying to write 248 bytes to the device with nRFConnect, can the "add...
Hi
I want to download the reference design of NRF52840 develop board, I found the follow address ...
http://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter...
