Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Hi
I am using SDK17. I am running the app_pwm example and i get an error with the "nrf_drv_state_t", it is not defined and the "NRF_DRV_STATE_POWERED_ON" is not defined...
Hello,
I'm programming nrf52 with SDK17. My application requires to advertise in 1 channel and also scan in 1 channel too. I have done the code. But when I run the code...
Hi,
I'm programming nRF52833 for my application. I have done to configure my device and it advertised and scanned sequentially. For my application, I advertise and also...
Hi:
I am trying the "Mesh Serial" example on my nrf52840 boards. However, when the Echo command is used after the device is cold-started , a timeout event will occur. I...
hai ,
i am using nrf52840 sdk 15.2 and in my application i have to connect nrf52840 central to peripheral after connection i have write data on ble_lbs_led_status_send i...
Hi,
I am using NR52832 with nRF5_SDK_15.3.0_59ac345 .
I want to scan nearby mobile BLE devices and get its data from its advertising data and also its scan response data...
Hi,
Hi, we have a latency-critical use-case and found the Low Latency Packet Mode ( LLPM ) as a possible solution.
Our current application is using nRF5 SDK 16.0 with...
Hello Devzone
Currently I am following below link to setup the “HID configurator for nRF Desktop”.
link: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf...
Hello, guys!
We are in an evaluation phase of our future product. Our plan is to use nRF52840-based module and the latest SDK 17.0.2 or FreeRTOS or Zephyr RTOS (will be...
Hello,
On the nRF 52840DK sdk 17and softdevice 140,
in example, peripheral „ble_app_template“ I need to transfer UUID, RSSI,... with time stamp to flash via FDS.
I advertise...
Hello,
The Bluetooth SIG has just released the LC3 Codec specifications on they website.
So my questions are:
- Can we use the nrf 52840 with this new codec for our...
I Flashed the DK using segger embedded studio with example "pca10056_s140_ble_debug" After that I am unable to flash "ble_app_uart" example.
I tried another example like...
Hello,
I am trying to do a long term connection test to the nrfcloud. I have updated the nordic sdk to v1.2.0 and am running the asset tracker on the dk board. I have set...
Hello,
I'm using nRF52840 chip with nRF5 SDK 15.2.0 ,Mesh SDK 3.1.0 and soft device S140 6.1.1
I'm trying to protect the flash if a shutdown occurs during a write. Reading...
From what I understand, the nRF52832 supports the following BLE5 features:
-2 Mbps
-CSA#2
-Advertising extensions
The chip does not support the 'Long Range' feature...
