Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Hello, everyone. I use sdk v17 and pca10040. I put the example 'pwm_library' in the example 'ble_app_uart'. However, 'NRFX_TIMER_INSTANCE (id)' in 'nrfx_timer.h' will generate...
Since upgrading from SDK 15.3.0 and soft device S140 6.1.1 to SDK 17.0.0 and S140 7.0.1, I can't get my custom bootloader to work. I adjusted the linker macros to what I think...
Hello.
I'm using Zigbee SDK 4.1.0 with custom pca10059-compatible debug board with nrf52840.
Binding and subscribing to attributes on a multiple endpoint device appears...
I am switching from standard Zephyr and I am trying out nRF connect SDK v1.3.0. When I am building my app for mcuboot, it hangs after configuring the child image (mcuboot...
I've got an application that reads MP3 files from an SD card, decodes them and outputs audio data to a codec via I2S. The codec is clocked by MCLK generated by the nRF. The...
hi Support Team
I am using 3 Development Kit flashed with Mesh Beaconing Example kept apart distance of 30mtr , Say A, B , C
In Another Kit I flashed ble_app_beacon Say...
Does `sd_ble_gatts_hvx()` queue indications and if so then when does the next message get sent; after the previous one is sent or after the receiver acks the previous one...
Hi
I have a project that uses several protocols, including UART and USB CLI
As such, I had to move the nRF logger to work on RTT, so that everything could work properly...
Hello,
I was wondering if it is possible to read the model (e.g. NRF52810_xxAA_REV1) from a chip with nrfjprog?
In production we use nrfjprog to program our devices and...
Platform: pca10100
SDK version: SDK17.0
Purpose: Use radio to scan Bluetooth devices and perform CTE sampling. When the scan data and IQ data accumulate nearly 4K, output...
I'm using a 52840 and need both low stand by current and use of a UART. I understand that the UART drives up the power so I'm trying to completely shut it down when not being...
Hi, everyone
I am studying openthread.
I had a nrf52840 Dongle(running CLI/MTD example) act as MTD node to join in the openthread network.
The Dongle's LEDS were removed...
Hello,
I am using a nRF DK (nRF52832 - PCA10040 - SDK 15) to communicate with a custom electronic device developed by my own company (which integrates an 1-Wire slave)....
Hello,
I have a question regarding eDRX mode on the nrf9160 in combination with NB-IoT. I tried to configure an eDRX cycle of 20.48s for the use in a battery powered actor...
Hello,
I am using the nRF52832 on a custom board, with SDK 15.2 and SD132 v6.1. My BLE application uses the SAADC to measure VCC voltage every 6 hours. I am using an app...
